- 您現在的位置：買賣IC網 > PDF目錄16707 > MAX14535EEVKIT+ (Maxim Integrated Products)KIT EVAL MAX14535E PDF資料下載
參數資料
| 型號： | MAX14535EEVKIT+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/13頁 |
| 文件大小： | 0K |
| 描述： | KIT EVAL MAX14535E |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 主要目的： | 接口，模擬開關 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MAX14535E |
| 主要屬性： | 1 x DPDT 開關 |
| 次要屬性： | 2.4 V ~ 5.5 V 電源 |
| 已供物品： | 板 |
MAX14535E–MAX14539E
Low-Resistance DPDT Switches
with Negative Rail
_______________________________________________________________________________________
7
Pin Description
PIN
NAME
FUNCTION
1
CB
Digital Control Input. Drive CB low to connect COM_ to NC_. Drive CB high to connect COM_ to NO_.
2EN
Active-High Enable Input. Drive EN high for normal operation. Drive EN low to put switches in high
impedance. Do not apply negative signals to NO_ or NC_ when EN is low (MAX14537E/MAX14538E).
3
NO2
Normally Open Terminal for Switch 2
4
COM2
Common Terminal for Switch 2
5
NC2
Normally Close Terminal for Switch 2
6
GND
Ground
7VCC
Positive Supply Voltage Input. Bypass VCC to GND with a 0.1F capacitor as close as possible to the
device.
8
NC1
Normally Close Terminal for Switch 1
9
COM1
Common Terminal for Switch 1
10
NO1
Normally Open Terminal for Switch 1
Detailed Description
The MAX14535E–MAX14539E are low on-resistance
and high ESD-protected single DPDT switches that
operate from a +2.4V to +5.5V supply and are
designed to multiplex AC-coupled analog signals.
These switches combine the low on-capacitance (CON)
and low on-resistance (RON) necessary for high-perfor-
mance switching applications. The negative signal
capability of the analog channel allows signals below
ground to pass through without distortion.
Analog Signal Levels
The MAX14535E
MAX14539E are bidirectional, allow-
ing NO_, NC_, and COM_ to be configured as either
inputs or outputs. Note that NC_ and NO_ are only pro-
tected against ESD up to ±2kV (Human Body Model)
and may require additional ESD protection if used as
outputs. These devices feature a charge pump that
generates a negative supply to allow analog signals as
low as -1.5V to pass through NO_, NC_, or COM_. This
allows AC-coupled signals that drop below ground to
pass even when operating from a 3.0V to 5.5V supply.
For the MAX14537E/MAX14538E, the negative charge
pump is controlled by the enable input and is active
when EN is high. When EN is driven low, the negative
charge pump is disabled, which puts the devices in the
lowest possible current consumption, and the signal
range is 0 to VCC. The negative charge pump is always
active for the MAX14535E/MAX14536E/MAX14539E,
therefore, a negative signal (at most -1.5V) can be
applied through NC_, NO_, or COM_, even when EN is
driven low. A negative rail signal (signal voltage < 0)
must not be applied to the switch unless the negative
charge pump is active.
Digital Control Input
The MAX14535E
MAX14539E provide a single-bit con-
trol logic input, CB. CB controls the switch position as
shown in the
Functional Diagrams. Drive CB rail-to-rail
to minimize power consumption.
Enable Input
The MAX14535E
MAX14539E feature a shutdown
mode that reduces the supply current (less than 1A
for MAX14537E/MAX14538E) and places the switches
in high impedance. Drive EN low to place the device in
shutdown mode. Drive EN high for normal operation.
Shunt Resistors
(MAX14535E/MAX14537E/MAX14539E)
When EN is high, the shunt resistors are controlled by
CB. When CB is low, NC_ is connected to COM_ and
NO_ is connected to shunt resistors. When CB is high,
NO_ is connected to COM_ and NC_ is connected to
shunt resistors (MAX14539E). When EN is low, all the
switches are open and all the shunt resistors are active.
Click-and-Pop Suppression
The 500
shunt resistors on the MAX14535E/
MAX14537E/MAX14539E automatically discharge any
capacitance at the NO_ terminals (or NC_ terminals,
MAX14539E) when they are unconnected from COM_.
This reduces audio click-and-pop sounds that may
occur when switching between capacitively coupled
audio sources.
相關PDF資料 |
PDF描述 |
|---|---|
| ZR431C01STZ | IC VREF SHUNT PREC ADJ TO-92-3 |
| EMC13DREH-S13 | CONN EDGECARD 26POS .100 EXTEND |
| V72B5E150B2 | CONVERTER MOD DC/DC 5V 150W |
| SC75-330 | INDUCTOR SMD 33UH 1.20A 2.52MHZ |
| RBA24DTKH | CONN EDGECARD 48POS DIP .125 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX14535EEVKIT+ | 功能描述:交換機 IC 開發工具 MAX14535E Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| MAX14536EEVB+ | 功能描述:IC SWITCH DPDT 10UTQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:- 電路:2 x SPST 導通狀態電阻:20 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3 V ~ 5.5 V 電流 - 電源:4.1mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:帶卷 (TR) |
| MAX14536EEVB+T | 功能描述:交換機 IC 開發工具 Low-Resistance DPDT Switch w/Neg Rail RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| MAX14539EEVB+T | 功能描述:交換機 IC 開發工具 Low-Resistance DPDT Switch w/Neg Rail RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| MAX14540AEEWP+T | 制造商:Maxim Integrated Products 功能描述:USB MULTIPLEXER INTERFACE CIRCUITS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。