欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MAX5965AEAX+
廠商: Maxim Integrated
文件頁數: 19/54頁
文件大小: 1334K
描述: IC PSE CTRLR FOR POE 36SSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 30
類型: 以太網供電控制器(PoE)
應用: IP 電話,LAN 網絡供電,網絡路由器和交換機
內部開關: 無
電源電壓: 2.4 V ~ 3.6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 36-BSOP(0.295",7.50mm 寬)
供應商設備封裝: 36-SSOP
包裝: 管件
High-Power, Quad, Monolithic, PSE Controllers
for Power over Ethernet
______________________________________________________________________________________   19
Powered Device Classification
(PD Classification)
During the PD classification mode, the MAX5965A/
MAX5965B force a probe voltage (-18V) at DET_ and
measure the current into DET_. The measured current
determines the class of the PD.
After each classification cycle, the device sets the
CL_END_ bit (R04h/05h[7:4]) high and reports the clas-
sification results in the status registers R0Ch[6:4],
R0Dh[6:4], R0Eh[6:4], and R0Fh[6:4]. The CL_END_ bit
is reset to low when read through register R05h or after
a port reset. Both events registers, R04h, and R05h are
cleared after the port powers down. Table 2 shows the
IEEE 802.3af requirement for a PSE classifying a PD at
the power interface (PI).
The MAX5965A/MAX5965B support high power beyond
the IEEE 802.3af standard by providing additional clas-
sifications (Class 5 and 2-event classification).
Class 5 PD Classification
During classification, if the MAX5965A/MAX5965B
detect currents in excess of I
CLASS
> 48mA, then the
PD will be classified as a Class 5 powered device.
Status registers R0Ch[6:4] or R0Dh[6:4] or R0Eh[6:4] or
R0Fh[6:4] will report the Class 5 classification result.
2-Event (Class 6) PD Classification
When 2-event classification is activated, the classifica-
tion cycle is repeated three times with 8ms wait time
between each cycle (see Figure 1b). Between each
classification cycle, the MAX5965A/MAX5965B do not
reset the port voltage completely but keeps the output
voltage at -9V. The EN_CL6 bits in R1Ch[7:4] enable 2-
event classification on a per port basis.
Powered State
When the MAX5965A/MAX5965B enter a powered
state, the t
START
and t
DISC
timers are reset. Before
turning on the port power, the MAX5965A/MAX5965B
check if any other port is not turning on and if the
t
FAULT
timer is zero. Another check is performed if the
ACD_EN_ bit is set, in this case the OSC_FAIL bit must
be low (oscillator is okay) for the port to be powered.
If these conditions are met, the MAX5965A/MAX5965B
enter startup where it turns on power to the port. An
internal signal, POK_, asserts high when V
OUT_
is within
2V from V
EE
. PGOOD_ status bits are set high if POK_
stays high longer than t
PGOOD
. PGOOD_ immediately
resets when POK_ goes low (see Figure 2).
The PG_CHG_ bit sets when a port powers up or down.
PWR_EN_ sets when a port powers up and resets when
a port shuts down. The port shutdown timer lasts 0.5ms
and prevents other ports from turning off during that peri-
od, except in the case of emergency shutdowns (RESET
= L, RESET_IC = H, V
EEUVLO,
V
DDUVLO,
and T
SHD
).
The MAX5965A/MAX5965B always check the status of
all ports before turning off. A priority logic system deter-
mines the order to prevent the simultaneous turn-on or
turn-off of the ports. The port with the lesser ordinal
number gets priority over the others (i.e., port 1 turns on
first, port 2 second, port 3 third, and port 4 fourth).
Setting PWR_OFF_ high turns off power to the corre-
sponding port.
Table 2. PSE Classification of a PD (Refer to Table 33-4 of the IEEE 802.3af)
MEASURED I
CLASS
 (mA)
CLASSIFICATION
0 to 5
Class 0
> 5 and < 8
May be Class 0 and 1
8 to 13
Class 1
> 13 and < 16
May be Class 1 or 2
16 to 21
Class 2
> 21 and < 25
May be Class 2 or 3
25 to 31
Class 3
> 31 and < 35
May be Class 3 or 4
35 to 45
Class 4
> 45 and < 51
May be Class 4 or 5
51 to 68
Class 5
相關PDF資料
PDF描述
MAX5969DETE+T IC CTRLR INTERFCE W/MOSFT 16TQFN
MAX5971AETI+ IC CTRLR PD IEEE 802.3AF 28WQFN
MAX5972AETE+T IC CONTROLLER INTERFACE 16TQFN
MAX5978ETJ+ IC CTLR HOT-SWAP 32TQFN
MAX5981BETE+ IC CTRLR PD IEEE 802.3AF 16TQFN
相關代理商/技術參數
參數描述
MAX5965AEAX+ 功能描述:熱插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5965AEAX+T 功能描述:熱插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5965AUAX+ 功能描述:熱插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5965AUAX+T 功能描述:熱插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5965BCAX+ 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
主站蜘蛛池模板: 内江市| 清新县| 教育| 金坛市| 龙陵县| 甘谷县| 泽库县| 安图县| 股票| 宜兰市| 辽中县| 丰顺县| 樟树市| 柳林县| 嫩江县| 吴忠市| 平和县| 抚州市| 田阳县| 潜山县| 山东省| 隆安县| 开封县| 侯马市| 美姑县| 景东| 宜丰县| 筠连县| 申扎县| 六枝特区| 察隅县| 紫云| 灵武市| 丰镇市| 义乌市| 罗定市| 贵阳市| 兴仁县| 许昌县| 阳曲县| 花莲市|