欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MAX5969DETE+T
廠商: Maxim Integrated
文件頁數: 8/16頁
文件大小: 1236K
描述: IC CTRLR INTERFCE W/MOSFT 16TQFN
標準包裝: 2,500
類型: 以太網供電控制器 PD 開關(PoE)
應用: 遠程外設(工業控制,相機,數據訪問)
內部開關:
電流限制: 720mA 至 880mA
電源電壓: 60V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-WQFN 裸露焊盤
供應商設備封裝: 16-TQFN-EP(5x5)
包裝: 帶卷 (TR)
IEEE 802.3af/at-Compliant, Powered Device Interface
Controller with Integrated Power MOSFET
8 ______________________________________________________________________________________
  Pin Description (continued)
PIN
NAME
FUNCTION
9
WAD
Wall Power Adapter Detector Input. Wall adapter detection is enabled the moment V
DD
 - V
SS
 crosses
the mark event threshold. Detection occurs when the voltage from WAD to RTN is greater than 9V.
When a wall power adapter is present, the isolation n-channel power MOSFET turns off, 2EC current
sink turns on. Connect WAD directly to RTN when the wall power adapter or other auxiliary power
source is not used.
10
PG
Open-Drain Power-Good Indicator Output. PG sinks 230FA to disable the downstream DC-DC
converter while turning on the hot-swap MOSFET switch. PG current sink is disabled during detection,
classification, and in the steady-state power mode. The PG current sink is turned on to disable the
downstream DC-DC converter when the device is in sleep mode.
11
2EC
2-Event Classification Detect or Wall Adapter Detect Output. A 1.5mA current sink is enabled at 2EC
when a Type 2 PSE or a wall adapter is detected. When powered by a Type 2 PSE, the 2EC current
sink is enabled after the isolation MOSFET is fully on until V
IN
 drops below the UVLO threshold. 2EC is
latched when powered by a Type 2 PSE until V
IN
 drops below the reset threshold. 2EC also asserts
when a wall adapter supply, typically greater than 9V, is applied between WAD and RTN. 2EC is not
latched if asserted by WAD. The 2EC current sink is turned off when the device is in sleep mode.
12
CLS
Classification Resistor Input. Connect a resistor (R
CLS
) from CLS to V
SS
 to set the desired classification
current. See the classification current specifications in the Electrical Characteristics table to find the
resistor value for a particular PD classification.

EP
Exposed Pad. Do not use EP as an electrical connection to V
SS
. EP is internally connected to V
SS
 
through a resistive path and must be connected to V
SS
 externally. To optimize power dissipation,
solder the exposed pad to a large copper power plane.
相關PDF資料
PDF描述
MAX5971AETI+ IC CTRLR PD IEEE 802.3AF 28WQFN
MAX5972AETE+T IC CONTROLLER INTERFACE 16TQFN
MAX5978ETJ+ IC CTLR HOT-SWAP 32TQFN
MAX5981BETE+ IC CTRLR PD IEEE 802.3AF 16TQFN
MAX5986AETE+ IC POE SWITCH PSE 16TQFN
相關代理商/技術參數
參數描述
MAX5970ETX+ 功能描述:熱插拔功率分布 Dual Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5970ETX+T 功能描述:熱插拔功率分布 Dual Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5970EVKIT+ 功能描述:電源管理IC開發工具 MAX5970 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
MAX5971AETI+ 功能描述:熱插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5971AETI+T 功能描述:熱插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
主站蜘蛛池模板: 玉田县| 定陶县| 静安区| 库车县| 兰坪| 池州市| 合川市| 灵川县| 丽水市| 贵德县| 安化县| 抚顺县| 辛集市| 全椒县| 军事| 社旗县| 河北省| 麻江县| 岑巩县| 广东省| 乌拉特后旗| 泽库县| 克东县| 嘉荫县| 绥阳县| 永靖县| 湘乡市| 枣强县| 株洲市| 望奎县| 修文县| 文登市| 三亚市| 成都市| 仙游县| 嘉兴市| 天镇县| 米林县| 水富县| 延吉市| 北海市|