- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5981BETE+ (Maxim Integrated)IC CTRLR PD IEEE 802.3AF 16TQFN Datasheet資料下載
參數資料
| 型號： | MAX5981BETE+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 13/16頁 |
| 文件大小： | 1328K |
| 描述： | IC CTRLR PD IEEE 802.3AF 16TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 類型： | 以太網供電控制器 PD 開關（PoE） |
| 應用： | 供電設備（PSE） |
| 內部開關： | 是 |
| 電流限制： | 720mA 至 880mA |
| 電源電壓： | 31 V ~ 60 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WQFN 裸露焊盤 |
| 供應商設備封裝： | 16-TQFN-EP（5x5） |
| 包裝： | 管件 |
IEEE 802.3af/at-Compliant, Powered Device Interface
Controllers with Integrated Power MOSFET
______________________________________________________________________________________ 13
Applications Information
Operation with 12V Adapter
Layout Procedure
Careful PCB layout is critical to achieve high efficiency
and low EMI. Follow these layout guidelines for optimum
performance:
1) Place the input capacitor, classification resistor, and
transient voltage suppressor as close as possible to
the MAX5981A/MAX5981B.
2) Use large SMT component pads for power dissipat-
ing devices such as the MAX5981A/MAX5981B and
the external diodes.
3) Use short and wide traces for high-power paths.
4) Use the MAX5981A/MAX5981B evaluation kit layout
as a reference.
5) Place enough vias in the pad for the EP of the
MAX5981A/MAX5981B so that heat generated inside
can be effectively dissipated by the PCB copper.
The recommended spacing for the vias is 1mm to
1.2mm pitch. The thermal vias should be plated (1oz
copper) and have a small barrel diameter (0.3mm to
0.33mm).
Figure 2. Typical Configuration When Using a 12V Wall Power Adapter
68nF
2-EVENT
CLASSIFICATION
(ASSERTED ON)
ENABLE
DC-DC
CONVERTER
IN+
IN-
RJ-45
AND
BRIDGE
RECTIFIER
GND
GND
-54V
SMAJ58A
MAX5981A
MAX5981B
R
DET
24.9kI
R
CLS
V
DD
V
SS
RTN
WAD
PG
DET
CLS
2EC/WAD
2EC
12V
BATTERY
1.5mA
THIS CIRCUIT ACHIEVES
PROPER 2EC LOGIC WHEN
BATTERY IS < 12.5V
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5986AETE+ | IC POE SWITCH PSE 16TQFN |
| MAX6509CAZK/V+T | IC TEMP SWITCH RES-PROG 5TSOT |
| MAX6513TT075+T | IC TEMP SWITCH REMOTE 6-TDFN |
| MAX6581TG9A+ | IC TEMP SENSOR 8-CH PREC 24-TQFN |
| MAX6602UE9A+T | IC TEMP MONITOR 5CH 16-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5981BETE+ | 功能描述:熱插拔功率分布 IEEE 802.3af/at PDIC Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5981BETE+T | 功能描述:熱插拔功率分布 IEEE 802.3af/at PDIC Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5982AETE+ | 功能描述:熱插拔功率分布 PDIC, up to 70W RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5982AETE+T | 功能描述:熱插拔功率分布 PDIC, up to 70W RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5982AEVKIT# | 制造商:Maxim Integrated Products 功能描述:PD INTERFACE CONTROLLER FOR HIGH POWER UP TO 70W APPLICATION - Boxed Product (Development Kits) 制造商:Maxim Integrated Products 功能描述:KIT EVAL FOR MAX5982A |
發布緊急采購，3分鐘左右您將得到回復。