欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MAX6616AEG+T
廠商: Maxim Integrated
文件頁數: 9/20頁
文件大小: 194K
描述: IC TEMP MON FAN CNTRL 24QSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
功能: 風扇控制,溫度監控器
傳感器類型: 內部和外部
感應溫度: 0°C ~ 140°C
精確度: ±1°C 本地(最大),±4°C 遠程(最大)
拓?fù)洌?/td> ADC
輸出類型: I²C?/SMBus?
輸出警報:
輸出風扇:
電源電壓: 3 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 24-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 24-QSOP
包裝: 帶卷 (TR)
brushless DC motor has enough time to operate. When
driving a fan with a PWM-to-DC circuit as shown in
Figure 5, the highest available frequency (35kHz) should
be used to minimize the size of the filter capacitors.
When using a fan with a PWM control input, the frequen-
cy normally should be high as well, although some fans
have PWM inputs that accept low-frequency drive.
The duty cycle of the PWM can be controlled in two ways:
1) Manual PWM control: setting the duty cycle of the fan
directly through the fan target duty-cycle registers
(0Bh and 0Ch).
2) Automatic PWM control: setting the duty cycle based
on temperature.
Manual PWM Duty-Cycle Control
Clearing the bits that select the temperature channels for
fan control (D5 and D4 for PWM1 and D3 and D2 for
PWM2) in the fan-configuration register (11h) enables
manual fan control. In this mode, the duty cycle written to
the fan target duty-cycle register directly controls the
corresponding fan. The value is clipped to a maximum of
240. Any value entered above that is changed to 240
automatically. In this control mode, the value in the maxi-
mum duty-cycle register is ignored and does not affect
the duty cycle used to control the fan.
Automatic PWM Duty-Cycle Control
In the automatic control mode, the duty cycle is con-
trolled by the local or remote temperature according to
the settings in the control registers. Below the fan-start
temperature, the duty cycle is either 0% or is equal to
the fan-start duty cycle, depending on the value of bit
D3 in the configuration byte register. Above the fan-
start temperature, the duty cycle increases by one
duty-cycle step each time the temperature increases by
one temperature step. The target duty cycle is calculat-
ed based on the following formula; for temperature >
FanStartTemperature:
where:
DC = DutyCycle
FSDC = FanStartDutyCycle
T = Temperature
FST = FanStartTemperature
DCSS = DutyCycleStepSize
TS = TempStep
Duty cycle is recalculated after each temperature con-
version if temperature is increasing. If the temperature
begins to decrease, the duty cycle is not recalculated
until the temperature drops by 5癈 from the last peak
temperature. The duty cycle remains the same until the
temperature drops 5癈 from the last peak temperature or
the temperature rises above the last peak temperature.
For example, if the temperature goes up to +85癈 and
starts decreasing, duty cycle is not recalculated until the
temperature reaches +80癈 or the temperature rises
above +85癈. If the temperature decreases further, the
duty cycle is not updated until it reaches +75癈.
For temperature < FanStartTemperature and D2 of
configuration register = 0:
DutyCycle = 0
For temperature < FanStartTemperature and D2 of
configuration register = 1:
DutyCycle = FanStartDutyCycle
Once the temperature crosses the fan-start temperature
threshold, the temperature has to drop below the fan-
start temperature threshold minus the hysteresis before
DC   FSDC    T   FST
DCSS
TS
=
+
?/DIV>
 
 (  
)  
-
Dual-Channel Temperature Monitors and
Fan-Speed Controllers with Thermistor Inputs
_______________________________________________________________________________________   9
+3.3V
PWM
18k&
27k&
10k&
120k&
+3.3V
+12V
500k&
V
OUT
 
TO FAN
1礔
1礔
0.01礔
0.1礔
Figure 5. Driving a Fan with a PWM-to-DC Circuit
V
CC
PWM
4.7k&
5V
Figure 6. Controlling a PWM Input Fan with the MAX6615/
MAX6616s PWM Output (Typically, the 35kHz PWM
Frequency Is Used)
相關PDF資料
PDF描述
MAX6622UE9A+T IC PREC TEMP MONITOR 5CH 16TSSOP
MAX6626RMTT+T IC TEMP SENSOR I2C 6-TDFN
MAX6627MKA#TG16 IC TEMP SENSOR DGTL SOT23-8
MAX6636UP9A+T IC PREC TEMP MONITOR 7CH 20TSSOP
MAX6639FATE+ IC 2CH TEMP MONITOR 16TQFN
相關代理商/技術參數
參數描述
MAX6616EVKIT 制造商:Maxim Integrated Products 功能描述:DUAL-CHANNEL TEMP MONITOR & FAN-SPE - Rail/Tube
MAX6618AUB+ 功能描述:接口 - 專用 PECI-to-I2C Translator RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX6618AUB+G126 功能描述:接口 - 專用 PECI-to-I2C Translator RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX6618AUB+T 功能描述:接口 - 專用 PECI-to-I2C Translator RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX6618AUB+TG11 功能描述:接口 - 專用 PECI-to-I2C Translator RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
主站蜘蛛池模板: 浙江省| 芜湖县| 大竹县| 临江市| 汕尾市| 尼勒克县| 罗甸县| 易门县| 颍上县| 壤塘县| 肇东市| 六盘水市| 吉木乃县| 大石桥市| 贵州省| 磐石市| 若羌县| 密云县| 肇源县| 闵行区| 蓬莱市| 友谊县| 清远市| 霍城县| 三明市| 榆树市| 安化县| 颍上县| 利川市| 梨树县| 梁河县| 丹巴县| 瓮安县| 海口市| 武功县| 泰和县| 涪陵区| 信宜市| 鹤峰县| 芜湖市| 东辽县|