欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MAX6649MUA/V+
廠商: Maxim Integrated
文件頁數: 8/16頁
文件大小: 194K
描述: IC SENSOR REMOTE SMBUS 8UMAX
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 50
功能: 溫度監控系統(傳感器)
傳感器類型: 內部和外部
感應溫度: -55°C ~ 125°C,外部傳感器
精確度: ±3°C 本地(最大),±3.2°C 遠程(最大)
拓撲: ADC,多路復用器,寄存器庫
輸出類型: I²C?/SMBus?
輸出警報:
輸出風扇:
電源電壓: 3 V ~ 5.5 V
工作溫度: -55°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-uMAX
包裝: 管件
+145癈 Precision SMBus-Compatible Remote/
Local Sensors with Overtemperature Alarms
8
Alarm Threshold Registers
Four registers store ALERT threshold valuesone high-
temperature (T
HIGH
) and one low-temperature (T
LOW
)
register each for the local and remote channels. If either
measured temperature equals or exceeds the corre-
sponding ALERT threshold value, the ALERT interrupt
asserts.
The MAX6646/MAX6647 local (internal) ALERT T
HIGH
register POR state is 0101 0101, or +85癈, while the
remote (external) ALERT T
HIGH
register POR state is
0101 1111, or +95癈.The MAX6649 POR state of both
ALERT T
HIGH
registers is 0101 0101, or +85癈. The POR
state of the local and remote T
LOW
registers for all
devices is 0000 0000, or 0癈.
Two additional registers store remote and local alarm
threshold data corresponding to the OVERT output. The
values stored in these registers are high-temperature
thresholds. If either of the measured temperatures equals
or exceeds the corresponding alarm threshold value, an
OVERT output asserts. The MAX6646/MAX6647 local
(internal) OVERT register POR state is 0101 0101, or
+85癈, while the remote (external) OVERT register POR
state is 0111 1101, or +125癈. The MAX6649 POR state
of both OVERT registers is 0101 0101, or +85癈.
Diode Fault Alarm
A continuity fault detector at DXP detects an open cir-
cuit between DXP and DXN, or a DXP short to V
CC
,
GND, or DXN. If an open or short circuit exists, the
external temperature register is loaded with 1111 1111.
If the fault is an open-circuit fault bit 2 (OPEN), the sta-
tus byte is set to 1. In the MAX6649, ALERT is activated
at the end of the conversion. Immediately after POR,
the status register indicates that no fault is present. If a
fault is present upon power-up, the fault is not indicated
until the end of the first conversion.
ALERT Interrupts
The ALERT interrupt occurs when the internal or external
temperature reading exceeds a high- or low-temperature
limit (programmed) or in the MAX6649, when the remote
diode is disconnected (for continuity fault detection). The
ALERT interrupt output signal is latched and can be
cleared only by either reading the status register or by
successfully responding to an alert response address. In
both cases, the alert is cleared if the fault condition no
longer exists. Asserting ALERT does not halt automatic
conversion. The ALERT output is open drain, allowing
multiple devices to share a common interrupt line.
The MAX6646/MAX6647/MAX6649 respond to the
SMBus alert response address, an interrupt pointer
return-address feature (see the Alert Response
Address section). Prior to taking corrective action,
always check to ensure that an interrupt is valid by
reading the current temperature.
Fault Queue Register
In some systems, it may be desirable to ignore a single
temperature measurement that falls outside the ALERT
limits. Bits 1 and 2 of the fault queue register (address
22h) determine the number of consecutive temperature
faults necessary to set ALERT (see Tables 3 and 4).
Alert Response Address
The SMBus alert response interrupt pointer provides
quick fault identification for simple slave devices that
lack the complex, expensive logic needed to be a bus
master. Upon receiving an ALERT interrupt signal, the
host master can broadcast a receive byte transmission
to the alert response slave address (0001 100).
Following such a broadcast, any slave device that gen-
erated an interrupt attempts to identify itself by putting
its own address on the bus.
SMBCLK
A
B
C
D
E    F
G
H
I    J   K
SMBDATA
t
SU:STA
t
HD:STA
t
LOW
t
HIGH
t
SU:DAT
t
HD:DAT
t
SU:STO
t
BUF
A = START CONDITION
B = MSB OF ADDRESS CLOCKED INTO SLAVE
C = LSB OF ADDRESS CLOCKED INTO SLAVE
D = R/W BIT CLOCKED INTO SLAVE
E = SLAVE PULLS SMBDATA LINE LOW
L
M
F = ACKNOWLEDGE BIT CLOCKED INTO MASTER
G = MSB OF DATA CLOCKED INTO MASTER
H = LSB OF DATA CLOCKED INTO MASTER
I = MASTER PULLS DATA LINE LOW
J = ACKNOWLEDGE CLOCKED INTO SLAVE
K = ACKNOWLEDGE CLOCK PULSE
L = STOP CONDITION
M = NEW START CONDITION
Figure 3. SMBus Read Timing Diagram
相關PDF資料
PDF描述
MAX6652AUB+T IC TEMP SENS/MON 10-UMAX
MAX6659MEE+T IC TEMP SENSOR SMBUS 16-QSOP
MAX6661AEE+T IC REG FAN SPEED 16-QSOP
MAX6664AEE+T IC TEMP MON FAN CNTRL 16-QSOP
MAX6665ASA45+ IC FAN CNTRL/DRVR 8-SOIC
相關代理商/技術參數
參數描述
MAX6649YMUA+ 功能描述:板上安裝溫度傳感器 145C SMBus-Comp Remote/Local Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6649YMUA+T 功能描述:板上安裝溫度傳感器 145C SMBus-Comp Remote/Local Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX664C/D 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MAX664CJA 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MAX664CPA 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
主站蜘蛛池模板: 卢湾区| 高唐县| 上思县| 宁南县| 尚义县| 花莲县| 常宁市| 元氏县| 茶陵县| 仙桃市| 观塘区| 城市| 成安县| 康平县| 双江| 恩施市| 保靖县| 长治县| 门头沟区| 聂拉木县| 宝坻区| 霍山县| 铁岭县| 平遥县| 河东区| 广安市| 大竹县| 奉化市| 东明县| 鲜城| 新平| 广水市| 九龙县| 朝阳区| 体育| 方山县| 调兵山市| 明水县| 玉田县| 吐鲁番市| 洪江市|