- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6649MUA/V+ (Maxim Integrated)IC SENSOR REMOTE SMBUS 8UMAX Datasheet資料下載
參數資料
| 型號： | MAX6649MUA/V+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 9/16頁 |
| 文件大小： | 194K |
| 描述： | IC SENSOR REMOTE SMBUS 8UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -55°C ~ 125°C，外部傳感器 |
| 精確度： | ±3°C 本地（最大），±3.2°C 遠程（最大） |
| 拓撲： | ADC，多路復用器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 管件 |
+145癈 Precision SMBus-Compatible Remote/
Local Sensors with Overtemperature Alarms
9
The alert response can activate several different slave
devices simultaneously, similar to the I
2
C general call. If
more than one slave attempts to respond, bus arbitration
rules apply, and the device with the lower address code
wins. The losing device does not generate an acknowl-
edge and continues to hold the ALERT line low until
cleared. (The conditions for clearing an ALERT vary,
depending on the type of slave device). Successful com-
pletion of the read alert response protocol clears the
interrupt latch, provided the condition that caused the
alert no longer exists.
OVERT Overtemperature Alarm/Warning
Outputs
OVERT asserts when the temperature rises to a value
stored in one of the OVERT limit registers (19h, 20h). It
deasserts when the temperature drops below the stored
limit, minus hysteresis. OVERT can be used to activate a
cooling fan, send a warning, invoke clock throttling, or trig-
ger a system shutdown to prevent component damage.
Command Byte Functions
The 8-bit command byte register (Table 5) is the master
index that points to the various other registers within the
MAX6646/MAX6647/MAX6649. The registers POR state
is 0000 0000, so a receive byte transmission (a protocol
that lacks the command byte) that occurs immediately
after POR, returns the current local temperature data.
The MAX6646/MAX6647/MAX6649 incorporate collision
avoidance so that completely asynchronous operation is
allowed between SMBus operations and temperature
conversions.
One-Shot
The one-shot command immediately forces a new con-
version cycle to begin. If the one-shot command is
received while the MAX6646/MAX6647/MAX6649 are in
standby mode (RUN bit = 1), a new conversion begins,
after which the device returns to standby mode. If a one-
shot conversion is in progress when a one-shot com-
mand is received, the command is ignored. If a one-shot
command is received in autonomous mode (RUN bit = 0)
between conversions, a new conversion begins, the con-
version rate timer is reset, and the next automatic conver-
sion takes place after a full delay elapses.
Configuration Byte Functions
The configuration byte register (Table 6) is a read-write
register with several functions. Bit 7 is used to mask (dis-
able) interrupts. Bit 6 puts the MAX6646/MAX6647/
MAX6649 into standby mode (STOP) or autonomous
(RUN) mode.
Status Byte Functions
The status byte register (Table 7) indicates which (if
any) temperature thresholds have been exceeded. This
byte also indicates whether the ADC is converting and
whether there is an open-circuit fault detected in the
external sense junction. After POR, the normal state of
all flag bits is zero, assuming no alarm conditions are
present. The status byte is cleared by any successful
read of the status byte, after conversion is complete
and if the fault condition no longer exists. Note that the
ALERT interrupt latch is not automatically cleared when
the status flag bit indicating the ALERT is cleared. The
fault condition must be eliminated before the ALERT
output can be cleared.
When autoconverting, if the T
HIGH
and T
LOW
limits are
close together, it is possible for both high-temp and low-
temp status bits to be set, depending on the amount of
time between status read operations (especially when
converting at the fastest rate). In these circumstances, it
is best not to rely on the status bits to indicate reversals in
long-term temperature changes. Instead use a current
temperature reading to establish the trend direction.
BIT
NAME
POR
STATE
FUNCTION
7
RFU
1
Reserved. Always write 1 to
this bit.
6 to 3
RFU
0
Reserved. Always write
zero to this bit.
2
FQ1
1
Fault queue-length control
bit (see Table 4).
1
FQ0
1
Fault queue-length control
bit (see Table 4).
0
RFU
0
Reserved. Always write
zero to this bit.
Table 3. Fault Queue Register Bit Definition
(22h)
FQ1
FQ0
FAULT QUEUE LENGTH (SAMPLES)
0
0
1
0
1
2
1
1
3
1
0
1
Table 4. Fault Queue Length Bit Definition
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6652AUB+T | IC TEMP SENS/MON 10-UMAX |
| MAX6659MEE+T | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6661AEE+T | IC REG FAN SPEED 16-QSOP |
| MAX6664AEE+T | IC TEMP MON FAN CNTRL 16-QSOP |
| MAX6665ASA45+ | IC FAN CNTRL/DRVR 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6649YMUA+ | 功能描述:板上安裝溫度傳感器 145C SMBus-Comp Remote/Local Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6649YMUA+T | 功能描述:板上安裝溫度傳感器 145C SMBus-Comp Remote/Local Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX664C/D | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX664CJA | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX664CPA | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。