- 您現在的位置：買賣IC網 > PDF目錄371001 > MC100EP111 (Motorola, Inc.) Low-Voltage 1:10 Differential ECL/PECL/HSTL Clock Driver(低壓1:10差分ECL/PECL/HSTL時鐘驅動器) PDF資料下載
參數資料
| 型號： | MC100EP111 |
| 廠商： | Motorola, Inc. |
| 英文描述： | Low-Voltage 1:10 Differential ECL/PECL/HSTL Clock Driver(低壓1:10差分ECL/PECL/HSTL時鐘驅動器) |
| 中文描述： | 低電壓1:10差動ECL / PECL的/ HSTL時鐘驅動器（低壓1:10差分ECL / PECL的/ HSTL時鐘驅動器） |
| 文件頁數： | 1/8頁 |
| 文件大小： | 149K |
| 代理商： | MC100EP111 |
SEMICONDUCTOR TECHNICAL DATA
Order this document
by MC100EP111/D
1
REV 1
Motorola, Inc. 2000
06/00
Low–Voltage 1:10 Differential
ECL/PECL/HSTL Clock Driver
The MC100EP111 is a low skew 1–to–10 differential driver, designed
with clock distribution in mind. It accepts two clock sources into an input
multiplexer. The ECL/PECL input signals can be either differential or
single–ended if the VBB output is used. HSTL inputs can be used when
the EP111 is operating under PECL conditions. The selected signal is
fanned out to 10 identical differential outputs.
100ps Part–to–Part Skew typical
35ps Output–to–Output Skew typical
Differential Design
VBB Output
Low Voltage VEE Range of –2.25 to –3.8V for ECL
Low Voltage VCC Range of +2.25 to +3.8V for PECL and HSTL
75k
Input Pulldown Resistors
ECL/PECL Outputs
The EP111 is specifically designed, modeled and produced with low
skew as the key goal. Optimal design and layout serve to minimize
gate–to–gate skew within a device, and empirical modeling is used to
determine process control limits that ensure consistent tpd distributions
from lot to lot. The net result is a dependable, guaranteed low skew
device.
To ensure that the tight skew specification is met it is necessary that both sides of the differential output are terminated into
50
, even if only one side is being used. In most applications, all ten differential pairs will be used and therefore terminated. In
the case where fewer than ten pairs are used, it is necessary to terminate at least the output pairs on the same package side as
the pair(s) being used on that side, in order to maintain minimum skew. Failure to do this will result in small degradations of
propagation delay (on the order of 10–20ps) of the output(s) being used which, while not being catastrophic to most designs, will
mean a loss of skew margin.
The MC100EP111, as with most other ECL devices, can be operated from a positive VCC supply in PECL mode. This allows
the EP111 to be used for high performance clock distribution in +3.3V or +2.5V systems. Designers can take advantage of the
EP111’s performance to distribute low skew clocks across the backplane or the board. In a PECL environment, series or
Thevenin line terminations are typically used as they require no additional power supplies. For more information on using PECL,
designers should refer to Motorola Application Note AN1406/D.
The MC100EP111 may be driven single–endedly utilizing the VBB bias output with the CLK0 input. If a single–ended signal is
to be used, the VBB pin should be connected to the CLK0 input and bypassed to ground via a 0.01
μ
F capacitor. The VBB output
can only source/sink 0.2mA; therefore, it should be used as a switching reference for the MC100EP111 only. Part–to–Part Skew
specifications are not guaranteed when driving the MC100EP111 single–endedly.
This document contains information on a new product. Specifications and information herein are subject to
change without notice.
LOW–VOLTAGE
1:10 DIFFERENTIAL
ECL/PECL/HSTL
CLOCK DRIVER
FA SUFFIX
32–LEAD LQFP PACKAGE
CASE 873A–02
相關PDF資料 |
PDF描述 |
|---|---|
| MC100H603FN | 9-Bit Latch ECL/TTL Translator |
| MC10H603 | 9-Bit Latch ECL/TTL Translator |
| MC10H603FN | 9-Bit Latch ECL/TTL Translator |
| MC100H642FN | 68030/040 PECL-TTL CLOCK DRIVER |
| MC10H642 | 68030/040 PECL-TTL CLOCK DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC100EP1111FA | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:LOW-VOLTAGE 1:10 DIFFERENTIAL ECL/PECL CLOCK DRIVER |
| MC100EP116 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:3.3 V / 5 V Hex Differential Line Receiver/Driver |
| MC100EP116FA | 功能描述:總線接收器 3.3V/5V Hex Diff RoHS:否 制造商:Texas Instruments 接收機數量:4 接收機信號類型:Differential 接口類型:EIA/TIA-422-B, V.11 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TSSOP-16 封裝:Reel |
| MC100EP116FAG | 功能描述:總線接收器 3.3V/5V Hex Diff RoHS:否 制造商:Texas Instruments 接收機數量:4 接收機信號類型:Differential 接口類型:EIA/TIA-422-B, V.11 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TSSOP-16 封裝:Reel |
| MC100EP116FAR2 | 功能描述:總線接收器 3.3V/5V Hex Diff RoHS:否 制造商:Texas Instruments 接收機數量:4 接收機信號類型:Differential 接口類型:EIA/TIA-422-B, V.11 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TSSOP-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。