- 您現在的位置：買賣IC網 > PDF目錄382300 > MC1GH128DACA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC1GH128DACA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 39/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC1GH128DACA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
39
Sep.22.2005
Revision 0.3
6.1 Card Identification Mode
While in card identification mode the host resets the card, validates operation voltage range, identifies the card and
assigns a Relative Card Address (RCA) to the card on the bus. All data communication in the Card Identification Mode
uses the command line (CMD) only.
6.1.1 Card Reset
After power-on by the host, the cards (even if it has been in
Inactive State)
is in MultiMediaCard mode (as opposed to SPI
mode) and in
Idle State.
Command GO_IDLE_STATE (CMD0) is the software reset command and puts the card into
Idle State.
It
is also used to
switch the card into SPI mode (refer to Chapter 7 for details).
After power-on, or CMD0, the cards’ output bus drivers are in high-impedance state and the card is initialized with a
default relative card address (0x0001“) and with a default driver stage register setting (lowest speed, highest driving cur-
rent capability). The host clocks the bus at the identification clock rate f
OD
(see Chapter 5.4.8).
CMD0 is valid in all states, with the exception of
Inactive
State
.
While in
Inactive
state the card does not accept CMD0,
unless it is used to switch the card into SPI mode.
6.1.2 Operating Voltage Range Validation
Each type of MultiMediaCard (either High voltage or Dual Voltage) shall be able to establish communication with the host,
as well as perform the actual card function (e.g. accessing memory), using any operating voltage within the voltage range
specified in this standard, for the given card type (See Chapter 5.4.2).
The SEND_OP_COND (CMD1) command is designed to provide MultiMediaCard hosts with a mechanism to identify and
reject cards which do not match the V
DD
range desired by the host. This is accomplished by the host sending the required
V
DD
voltage window as the operand of this command (See Chapter 5.5.1). If the card can not perform data transfer in the
specified range it must discard itself from further bus operations and go into
Inactive State
. Otherwise, the card shall
respond sending back its V
DD
range. For this, the levels in the OCR register shall be defined accordingly (see Chapter
5.5.1).
相關PDF資料 |
PDF描述 |
|---|---|
| MC1GH128NACA-2SA00 | SAMSUNG MultiMediaCard |
| MC1GH256DACA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH01GDMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH256NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512DMCA-2SA00 | SAMSUNG MultiMediaCard |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1GH128NACA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC1GH256DACA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC1GU016HACA | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HACA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HACB-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
發布緊急采購，3分鐘左右您將得到回復。