- 您現在的位置：買賣IC網 > PDF目錄382300 > MC1GH128DACA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC1GH128DACA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 70/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC1GH128DACA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁當前第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
70
Sep.22.2005
Revision 0.3
Bits
Identifier
Type
Det-
Mode
Value
Description
Clear
Cond
19
ERROR
E
X
’0’= no error
’1’= error
(Undefined by the standard)
A generic card error related to the (and
detected during) execution of the last host
command (e.g. read or write failures).
C
18 -
17
Not applicable. This bit is always set to 0.
16
CID/
CSD_OVERWRITE
E
X
’0’= no error
’1’= error
Can be either one of the following errors:
- The CID register has been already written
and can not be overwritten
- The read only section of the CSD does not
match the card content.
- An attempt to reverse the copy (set as origi-
nal) or permanent WP (unprotected) bits was
made.
C
15
WP_ERASE_SKIP
E
X
’0’= not protected
’1’= protected
Only partial address space was erased due to
existing write protected blocks.
C
14
Reserved, must be set to 0
13
ERASE_RESET
E
R
’0’= cleared
’1’= set
An erase sequence was cleared before exe-
cuting because an out of erase sequence
command was received (commands other
than CMD35, CMD36, CMD38 or CMD13
C
12:9
CURRENT_STATE
S
R
0 = Idle
1 = Ready
2 = Ident
3 = Stby
4 = Tran
5 = Data
6 = Rcv
7 = Prg
8 = Dis
9 = Btst
10-15 = reserved
The state of the card when receiving the com-
mand. If the command execution causes a
state change, it will be visible to the host in
the response on the next command.
The four bits are interpreted as a binary num-
ber between 0 and 15.
B
8
READY_FOR_DATA
S
R
’0’= not ready
’1’= ready
Corresponds to buffer empty signalling on the
bus
A
7
SWITCH_ERROR
E
X
’0’= no error
’1’= switch error
If set, the card did not switch to the expected
mode as requested by the SWITCH com-
mand
C
6
Reserved
5
Not applicable. This bit is always set to 0.
4
Reserved
3:2
Reserved for Application Specific commands
1:0
Reserved for Manufacturer Test Mode
Table 6-22 : Card Status
相關PDF資料 |
PDF描述 |
|---|---|
| MC1GH128NACA-2SA00 | SAMSUNG MultiMediaCard |
| MC1GH256DACA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH01GDMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH256NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512DMCA-2SA00 | SAMSUNG MultiMediaCard |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1GH128NACA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC1GH256DACA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC1GU016HACA | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HACA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HACB-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
發布緊急采購，3分鐘左右您將得到回復。