- 您現在的位置：買賣IC網 > PDF目錄382300 > MC1GH256DACA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC1GH256DACA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 52/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC1GH256DACA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
52
Sep.22.2005
Revision 0.3
Note that the password length register (PWD_LEN) indicates if a password is currently set. When it equals ‘0’ there is no
password set. If the value of PWD_LEN is not equal to zero the card will lock itself after power up. It is possible to lock the
card immediately in the current power session by setting the LOCK/UNLOCK bit (while setting the password) or sending
additional command for card lock.
Reset the Password:
Select the card (CMD7), if not previously selected already
Define the block length (CMD16), given by the 8 bit card lock/unlock mode, the 8 bit password size (in bytes), and
the number of bytes of the currently used password.
Send the card lock/unlock command with the appropriate data block size on the data line including 16 bit CRC.
The data block shall indicate the mode CLR_PWD, the length (PWD_LEN) and the password (PWD) itself (LOCK/
UNLOCK bit is don’t care). If the PWD and PWD_LEN content match the sent password and its size, then the con
tent of the PWD register is cleared and PWD_LEN is set to 0. If the password is not correct then the
LOCK_UNLOCK_FAILED error bit will be set in the status register.
Locking a card:
Select the card (CMD7), if not previously selected already
Define the block length (CMD16), given by the 8 bit card lock/unlock mode, the 8 bit password size (in bytes), and
the number of bytes of the currently used password.
Send the card lock/unlock command with the appropriate data block size on the data line including 16 bit CRC. The
data block shall indicate the mode LOCK, the length (PWD_LEN) and the password (PWD) itself.
If the PWD content equals to the sent password then the card will be locked and the card-locked status bit will be set in the
status register. If the password is not correct then LOCK_UNLOCK_FAILED error bit will be set in the status register.
Note that it is possible to set the password and to lock the card in the same sequence. In such case the host shall perform
all the required steps for setting the password (as described above) including the bit LOCK set while the new password
command is sent.
If the password was previously set (PWD_LEN is not ‘0’), then the card will be locked automatically after power on reset.
An attempt to lock a locked card or to lock a card that does not have a password will fail and the LOCK_UNLOCK_FAILED
error bit will be set in the status register.
Unlocking the card:
Select the card (CMD7), if not previously selected already.
Define the block length (CMD16), given by the 8 bit card lock/unlock mode, the 8 bit password size (in bytes), and
the number of bytes of the currently used password.
Send the card lock/unlock command with the appropriate data block size on the data line including 16 bit CRC. The
data block shall indicate the mode UNLOCK, the length (PWD_LEN) and the password (PWD) itself.
If the PWD content equals to the sent password then the card will be unlocked and the card-locked status bit will be
cleared in the status register. If the password is not correct then the LOCK_UNLOCK_FAILED error bit will be set in the
status register.
Note that the unlocking is done only for the current power session. As long as the PWD is not cleared the card will be
locked automatically on the next power up. The only way to unlock the card is by clearing the password.
An attempt to unlock an unlocked card will fail and LOCK_UNLOCK_FAILED error bit will be set in the status register.
相關PDF資料 |
PDF描述 |
|---|---|
| MC2GH01GDMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH256NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512DMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH01GNMCA-2SA00 | SAMSUNG MultiMediaCard |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1GU016HACA | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HACA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HACB-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HACC-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HAFA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
發布緊急采購，3分鐘左右您將得到回復。