欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC2GH512NMCA-2SA00
廠商: SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述: SAMSUNG MultiMediaCard
中文描述: 三星多媒體
文件頁數: 72/102頁
文件大小: 1384K
代理商: MC2GH512NMCA-2SA00
MultiMediaCard
TM
72
Sep.22.2005
Revision 0.3
6.12 Timing Diagrams
All timing diagrams use the following schematics and abbreviations:
The difference between the P-bit and Z-bit is that a P-bit is actively driven to HIGH by the card respectively host output
driver, while Z-bit is driven to (respectively kept) HIGH by the pull-up resistors R
CMD
respectively R
DAT
. Actively-driven P-
bits are less sensitive to noise.
All timing values are defined in Table 6-25.
6.12.1 Command and Response
Both host command and card response are clocked out with the rising edge of the host clock.
Card identification and card operation conditions timing
The card identification (CMD2) and card operation conditions (CMD1) timing are processed in the open-drain mode. The
card response to the host command starts after exactly N
ID
clock cycles.
Figure 6-7 : Identification Timing (Card Identification Mode)
Assign a card relative address
The SET_RCA (CMD 3) is also processed in the open-drain mode. The minimum delay between the host command and
card response is N
CR
clock cycles.
Figure 6-8 : SET_RCA Timing (Card Identification Mode)
Symbol
Definition
S
Start bit (= ‘0’)
T
Transmitter bit (Host = ‘1’, Card = ‘0’)
P
One-cycle pull-up (= ‘1’)
E
End bit (=’1’)
Z
High impedance state (-> = ‘1’)
X
Driven value, ‘1’ or ‘0’
D
Data bits
*
Repetition
CRC
Cyclic redundancy check bits (7 bits)
Card active
Host active
Table 6-24 : Timing Diagram Symbols
Host Command
→ ←
N
ID
cycles
S T
content
CRC E Z
CID or OCR
content
CMD
* * *
Z S T
Z Z Z
Host Command
N
CR
cycles
S T
content
CRC E Z
Response
content
CRC E Z Z Z
CMD
* * *
Z S T
相關PDF資料
PDF描述
MC4GH01GNMCA-2SA00 SAMSUNG MultiMediaCard
MC4GH02GNMCA-2SA00 SAMSUNG MultiMediaCard
MC206 THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT
MC2300 Navigator Motion Processor
MC26LS30 Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers
相關代理商/技術參數
參數描述
MC2GU01GNMCA-0QC00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC2GU512NMCA-0QC00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC2M 制造商:G & J HALL 功能描述:STEP DRILL 10-20MM 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP; Drill Bit Size Metric:10mm; Overall Length:77.5mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Material:Steel; Material Thickness Max:4mm; Range:10mm - 20mm; Range:10mm - 20mm; Shank Dia:9mm; ;RoHS Compliant: NA
MC2N2906A 制造商:SPC Multicomp 功能描述:BIPOLAR TRANSISTOR, PNP, -60V TO-18; Transistor Polarity:PNP; Collector Emitter Voltage V(br)ceo:-60V; Transition Frequency Typ ft:200MHz; Power Dissipation Pd:400mW; DC Collector Current:-600mA; DC Current Gain hFE:40; No. of Pins:3;RoHS Compliant: Yes
MC3 制造商:Omron Corporation 功能描述:CONTROLLER,DIN MOUNT,24 VDC,SAFETY MAT CONTROLLER 制造商:Carlo Gavazzi 功能描述:MAGNETIC RECTANGULAR PROX. SENSOR
主站蜘蛛池模板: 南阳市| 崇文区| 滦南县| 遂昌县| 唐山市| 锡林浩特市| 巴楚县| 涡阳县| 锦州市| 长子县| 康乐县| 井研县| 洛隆县| 富裕县| 宝兴县| 林甸县| 调兵山市| 天峨县| 治多县| 抚远县| 苍山县| 永胜县| 镶黄旗| 渑池县| 榕江县| 梨树县| 建湖县| 许昌县| 从化市| 酉阳| 阿拉善左旗| 上饶县| 永年县| 尼木县| 封开县| 淮北市| 凤台县| 健康| 南澳县| 永吉县| 平江县|