欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC56F8356
廠商: Motorola, Inc.
英文描述: 56F8356 16-bit Hybrid Controller
中文描述: 56F8356 16位混合控制器
文件頁數: 115/160頁
文件大小: 1380K
代理商: MC56F8356
Flash Access Blocking Mechanisms
56F8356 Technical Data
Preliminary
115
7.2.2
On-chip Flash can be read by issuing commands across the EOnCE port, which is the debug
interface for the 56800E core. The TRST, TCLK, TMS, TDO, and TDI pins comprise a JTAG
interface onto which the EOnCE port functionality is mapped. When the 56F8356 boots, the
chip-level JTAG TAP (Test Access Port) is active and provides the chip’s boundary scan capability
and access to the ID register.
Disabling EOnCE Access
Proper implementation of Flash security requires that no access to the EOnCE port is provided
when security is enabled. The 56800E core has an input which disables reading of internal memory
via the JTAG/EOnCE. The FM sets this input at reset to a value determined by the contents of the
FM security bytes.
7.2.3
If a user inadvertently enables security on the 56F8356, a lockout recovery mechanism is provided
which allows the complete erasure of the internal Flash contents, including the configuration field,
and thus disables security (the protection register is cleared). This does not compromise security,
as the entire contents of the user’s secured code stored in Flash are erased before security is
disabled on the 56F8356 on the next reset or power-up sequence. To start the lockout recovery
sequence, the JTAG public instruction (LOCKOUT_RECOVERY) must first be shifted into the
chip-level TAP controller’s instruction register.
Flash LOCKOUT_RECOVERY
The LOCKOUT_RECOVERY instruction will have an associated 7-bit Data Register (DR) that is
used to control the clock divider circuit within the FM module. This divider, FM_CLKDIV[6:0],
is used to control the period of the clock used for timed events in the FM erase algorithm. This
register must be set with appropriate values before the lockout sequence can begin. Refer to the
JTAG section of the
56F8300 Peripheral User Manual
for more details on setting this register
value.
The value of the JTAG FM_CLKDIV[6:0] will replace the value of the FM register FMCLKD that
divides down the system clock for timed events, as illustrated in
Figure 7-1
. FM_CLKDIV[6] will
map to the PRDIV8 bit, and FM_CLKDIV[5:0] will map to the DIV[5:0] bits. The combination of
PRDIV8 and DIV must divide the FM input clock down to a frequency of 150kHz-200kHz. The
“Writing the FMCLKD Register
” section in the Flash Memory chapter of the
56F8300
Peripheral User Manual
gives specific equations for calculating the correct values.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC56F8356VFV60 56F8356 16-bit Hybrid Controller
MC56F8356MFV60 56F8356 16-bit Hybrid Controller
MC56F8357 16-bit Digital Signal Processor
MC56F8357 16-BIT HYBRID CONTROLLERS
MC56F8357MPY60 16-bit Digital Signal Processor
相關代理商/技術參數
參數描述
MC56F8356MFV60 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC56F8356MFVE 功能描述:數字信號處理器和控制器 - DSP, DSC 16 BIT HYBRID CONTROLLER RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8356VFV60 功能描述:數字信號處理器和控制器 - DSP, DSC 60MHz 60MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8356VFVE 功能描述:數字信號處理器和控制器 - DSP, DSC 60MHz 60MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8357 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-BIT HYBRID CONTROLLERS
主站蜘蛛池模板: 云阳县| 本溪市| 东辽县| 南丰县| 中阳县| 萨嘎县| 松潘县| 吉隆县| 苍山县| 峨眉山市| 伽师县| 仙居县| 延边| 宁国市| 收藏| 若尔盖县| 长葛市| 武川县| 大余县| 博野县| 舟曲县| 东兴市| 乌海市| 枣强县| 河南省| 崇义县| 卢氏县| 河池市| 道孚县| 上蔡县| 阜平县| 莱芜市| 绿春县| 巴中市| 永吉县| 商河县| 福安市| 治多县| 保德县| 东港市| 香河县|