欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68HC11A8BMP2
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: HCMOS Single-Chip Microcontroller
中文描述: 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP48
封裝: DIP-48
文件頁數: 59/158頁
文件大小: 776K
代理商: MC68HC11A8BMP2
MC68HC11A8
TECHNICAL DATA
SERIAL PERIPHERAL INTERFACE
MOTOROLA
6-1
6
6 SERIAL PERIPHERAL INTERFACE
This section contains a description on the serial peripheral interface (SPI).
6.1 Overview and Features
The serial peripheral interface (SPI) is a synchronous interface which allows several
SPI microcontrollers or SPI-type peripherals to be interconnected. In a serial periph-
eral interface, separate wires (signals) are required for data and clock. In the SPI for-
mat, the clock is not included in the data stream and must be furnished as a separate
signal. The MC68HC11A8 SPI system may be configured either as a master or as a
slave. The SPI contains the following features:
Full Duplex, Three-Wire Synchronous Transfers
Master or Slave Operation
1.5 MHz (Maximum) Master Bit Frequency
3 MHz (Maximum) Slave Bit Frequency
Four Programmable Master Bit Rates
Programmable Clock Polarity and Phase
End-of-Transmission Interrupt Flag
Write Collision Flag Protection
Master-Master Mode Fault Protection
Easily Interfaces to Simple Expansion Parts (PLLs, D/As, Latches, Display Driv-
ers, etc.)
6.2 SPI Signal Descriptions
The four basic SPI signals (MISO, MOSI, SCK, and SS) are discussed in the following
paragraphs. Each signal is described for both the master and slave modes.
Any SPI output line has to have its corresponding data direction register bit set. If this
bit is clear, the line is disconnected from the SPI logic and becomes a general-purpose
input line. Any SPI input line is forced to act as an input regardless of what is in the
corresponding data direction register bit.
6.2.1 Master In Slave Out (MISO)
The MISO line is configured as an input in a master device and as an output in a slave
device. It is one of the two lines that transfer serial data in one direction, with the most
significant bit sent first. The MISO line of a slave device is placed in the high-imped-
ance state if the slave is not selected.
6.2.2 Master Out Slave In (MOSI)
The MOSI line is configured as an output in a master device and as an input in a slave
device. It is one of the two lines that transfer serial data in one direction with the most
significant bit sent first.
相關PDF資料
PDF描述
MC68HC11A8BVP2 HCMOS Single-Chip Microcontroller
MC68HC11A1CFN2 HCMOS Single-Chip Microcontroller
MC68HCP11A1CFN2 HCMOS Single-Chip Microcontroller
MC68HCP11A1CFN3 HCMOS Single-Chip Microcontroller
MC68HCP11A1CP2 HCMOS Single-Chip Microcontroller
相關代理商/技術參數
參數描述
MC68HC11A8BVP2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
MC68HC11A8FN 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers
MC68HC11A8FN1 制造商:Motorola Inc 功能描述:
MC68HC11A8MCFN2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
MC68HC11A8P1 制造商:Rochester Electronics LLC 功能描述:- Bulk
主站蜘蛛池模板: 昭平县| 淳安县| 紫云| 建昌县| 武山县| 万年县| 兴安盟| 湘乡市| 汉阴县| 沙湾县| 灌云县| 孙吴县| 霍城县| 于田县| 运城市| 馆陶县| 屏东市| 平山县| 九龙城区| 剑阁县| 长垣县| 固镇县| 青海省| 大渡口区| 桂东县| 吉林市| 开江县| 襄垣县| 曲靖市| 吴旗县| 虎林市| 新野县| 广丰县| 漠河县| 沙河市| 靖西县| 星子县| 房产| 桃园县| 凤庆县| 全南县|