欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: NCP1083DEG
廠商: ON Semiconductor
文件頁數: 13/18頁
文件大小: 257K
描述: IC CONV CTLR POE-PD 40W 20-TSSOP
標準包裝: 74
類型: 以太網供電開關(PoE)
應用: 遠程外設(工業控制,相機,數據訪問)
內部開關:
電流限制: 1.1A
電源電壓: 0 V ~ 57 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-TSSOP(0.173",4.40mm 寬)裸露焊盤
供應商設備封裝: 20-TSSOP-EP
包裝: 管件
NCP1083
http://onsemi.com
13
" The PSE skipped the classification phase.
" The PSE performed a one event hardware classification
(it can be a IEEE 802.3af or a 802.3at compliant PSE
with Layer 2 engine).
" The PSE performed a two event hardware classification
but it did not properly control the input voltage in the
mark voltage window, (for example it crossed the reset
range).
Power Mode
When the classification handshake is completed, the
PSE and PD devices move into the operating mode.
Under Voltage Lock Out (UVLO)
The NCP1083 incorporates an under voltage lock out
(UVLO) circuit which monitors the input voltage and
determines when to apply power to the DCDC controller.
To use the default settings for UVLO (see Table 3), the pin
UVLO must be connected to VPORTN
1,2
. In this case the
signature resistor has to be placed directly between
VPORTP and VPORTN
1,2
, as shown in Figure 11.
Figure 11. Default UVLO Settings
UVLO
VPORTP
VPORTN1,2
NCP1083
VPORT
Rdet
To define the UVLO threshold externally, the UVLO pin
must be connected to the center of an external resistor
divider between VPORTP and VPORTN
1,2
 as shown in
Figure 12. The series resistance value of the external
resistors must add to 25.5 kW and replaces the internal
signature resistor.
Figure 12. External UVLO Configuration
UVLO
VPORTN1,2
NCP1083
VPORT
R2
R1
VPORTP
For a Vuvlo_on desired turnon voltage threshold, R1 and
R2 can be calculated using the following equations:
R1 ) R2 + R
det
R2 +
1.2
V
ulvo_on
  R
det
When using the external resistor divider, the NCP1083 has
an external reference voltage hysteresis of 15 percent typical.
Auxiliary Supply Support
To support applications connected to nonPoE enabled
networks and minimize the bill of materials, the NCP1083
supports drawing power from an external supply. The
NCP1083 supports the IEEE 802.3af/at standard when PoE
power sourcing is available and acts as a regular DCDC
converter when there is no power source available on the
Ethernet cable as shown in Figure 13.
Auxiliary supply support can be implemented in three
ways depending on where the auxiliary supply is injected.
The front, rear and direct auxiliary supply configurations are
explained in more detail in the application note AND9080.
UVLO
VPORTN1,2
NCP1083
VPORTP
Rdet1
Raux2
VAUX(+)
Rdet2
Pass
Switch
RTN
Raux1
Raux3
AUX
D1
D2
POE(+)
POE()
VPORT
Cpd
DCDC Stage
VAUX()
to VPORTN1,2 (Front AUX Configuration)
to RTN (Rear AUX Configuration)
Or
Figure 13. Front and Rear Auxiliary Supply Input with Support for Very Low Input Voltages
Optional 
for very low
VAUX only
相關PDF資料
PDF描述
NCP1501DMR2G IC REG SGL BUCK/LINEAR 8MICRO
NCP1578MNR2G IC REG DL BCK/LINEAR SYNC 20-QFN
NCP1601BDR2G IC PFC CTRL CRM/TRANSITION 8SOIC
NCP1603D100R2G IC CTLR PFC/PWM COMBO 16-SOIC
NCP1605DR2G IC PFC CONTROLLER CCM/DCM 16SOIC
相關代理商/技術參數
參數描述
NCP1083DER2G 功能描述:DC/DC 開關控制器 POE-PD 40W DC-DC AUX SUPP RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
NCP1083QBCGEVB 功能描述:電源管理IC開發工具 HIGH POWER POE-PD MODULE RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
NCP1083WIRGEVB 功能描述:電源管理IC開發工具 POE-PD MODULE WITH VAUX RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
NCP1086 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator
NCP1086/D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator
主站蜘蛛池模板: 德保县| 双鸭山市| 闽侯县| 博湖县| 获嘉县| 家居| 尼勒克县| 崇文区| 阿克陶县| 定安县| 金秀| 武宣县| 罗田县| 德庆县| 万州区| 正定县| 永城市| 桂平市| 巩义市| 同江市| 高雄县| 大邑县| 福贡县| 栾川县| 宝鸡市| 林州市| 开远市| 乐平市| 修文县| 文山县| 通渭县| 宁武县| 金平| 称多县| 江阴市| 文化| 鸡泽县| 黄石市| 湖北省| 体育| 万宁市|