- 您現在的位置：買賣IC網 > PDF目錄361091 > NCP1395ADR2G (ON SEMICONDUCTOR) High Performance Resonant Mode Controller PDF資料下載
參數資料
| 型號： | NCP1395ADR2G |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | High Performance Resonant Mode Controller |
| 中文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | LEAD FREE, SOIC-8 |
| 文件頁數： | 15/27頁 |
| 文件大小： | 345K |
| 代理商： | NCP1395ADR2G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
NCP1395A/B
http://onsemi.com
15
Finally, Two Circuit Versions, A and B:
The A and
B versions differ because of the following changes:
1. The startup thresholds are different, the A starts
to pulse for V
CC
= 12.8 V whereas the B pulses
for V
CC
= 10 V. The turn off levels are the
same, however. The A is recommended for
consumer products where the designer can use
an external startup resistor, whereas the B is
more recommended for industrial/medical
applications where a 12 V auxiliary supply
directly powers the chip.
2. The A version does not activate the softstart
upon release of the fast fault input. This is to let
the designer implement skip cycle. To the
opposite, the B version goes back to operation
upon the fast fault pin release via a softstart
sequence.
VoltageControlled Oscillator
The VCO section features a highspeed circuitry
allowing an internal operation from 100 kHz up to
2.0 MHz. However, as a division by two internally creates
the two Q and Qbar outputs, the final effective signal on
output A and B switches between 50 kHz and 1.0 MHz.
The VCO is configured in such a way that if the feedback
pin goes up, the switching frequency also goes up.
Figure 33 shows the architecture of this oscillator.
Vref
Vdd
Fmin
Rtm sets
Fmin for V(FB) < Vfb_off
Cint
Imin
+
0 to I_Fmax
IDT
FBinternal
max
Fsw
max
+
+
Clk
D
S
Q
Q
R
A
B
Vref
Vdd
Rdt sets
the deadtime
DT
Imin
Vdd
Fmax
Rtmax sets
the maximum Fsw
Vcc
FB
Rfb
20 k
+
+
Vfb < Vb_fault
start fault timer
Figure 33. Simplified VCO Architecture
Vb_fault
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1395BDR2G | High Performance Resonant Mode Controller |
| NCP1395BPG | High Performance Resonant Mode Controller |
| NCP1395A | High Performance Resonant Mode Controller(高性能諧振模式控制器) |
| NCP1395B | High Performance Resonant Mode Controller(高性能諧振模式控制器) |
| NCP1400A(中文) | 100 mA, Fixed Frequency PWM Step-Up Micropower Switching Regulator(100mA,固定頻率PWM升壓微功率開關穩壓器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1395APG | 功能描述:電壓模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| NCP1395B | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Resonant Mode Controller |
| NCP1395BDR2G | 功能描述:電壓模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| NCP1395BPG | 功能描述:電壓模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| NCP1395D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Resonant Mode Controller |
發布緊急采購，3分鐘左右您將得到回復。