- 您現在的位置：買賣IC網 > PDF目錄361091 > NCP1395ADR2G (ON SEMICONDUCTOR) High Performance Resonant Mode Controller PDF資料下載
參數資料
| 型號： | NCP1395ADR2G |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | High Performance Resonant Mode Controller |
| 中文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | LEAD FREE, SOIC-8 |
| 文件頁數： | 19/27頁 |
| 文件大小： | 345K |
| 代理商： | NCP1395ADR2G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
NCP1395A/B
http://onsemi.com
19
1
ires1
2
vout
20.0
10.0
0
10.0
20.0
i
P
1
200u
600u
1.00m
1.40m
1.80m
time in seconds
169
171
173
175
177
v
P
2
SS Action
Ires
Target is
reached
Vout
Figure 42. SoftStart Behavior
Figure 43. A Typical Startup Sequence on an LLC
Converter
Please note that the softstart will be activated in the
following conditions:
A startup sequence
During autorecovery burst mode
A brownout recovery
A temperature shutdown recovery
The fast fault input undergoes a special treatment. Since
we want to implement skip cycle through the fast fault
input on the NCP1395A, we cannot activate the softstart
every time the feedback pin stops the operations in low
power mode. Therefore, when the fast fault pin is released,
no softstart occurs to offer the best skip cycle behavior.
However, it is very possible to combine skip cycle and true
fast fault input, e.g. via ORing diodes driving pin 13. In that
case, if a signal maintains the fast fault input high long
enough to bring the feedback level down (that is to say
below 0.6 V) since the output voltage starts to fall down,
then the softstart is activated after the release of the pin.
In the B version tailored to operate from an auxiliary
12 V power supply, the softstart is always activated upon
the fast fault input release, whatever the feedback
condition is.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1395BDR2G | High Performance Resonant Mode Controller |
| NCP1395BPG | High Performance Resonant Mode Controller |
| NCP1395A | High Performance Resonant Mode Controller(高性能諧振模式控制器) |
| NCP1395B | High Performance Resonant Mode Controller(高性能諧振模式控制器) |
| NCP1400A(中文) | 100 mA, Fixed Frequency PWM Step-Up Micropower Switching Regulator(100mA,固定頻率PWM升壓微功率開關穩壓器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1395APG | 功能描述:電壓模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| NCP1395B | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Resonant Mode Controller |
| NCP1395BDR2G | 功能描述:電壓模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| NCP1395BPG | 功能描述:電壓模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| NCP1395D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Resonant Mode Controller |
發布緊急采購，3分鐘左右您將得到回復。