- 您現在的位置：買賣IC網 > PDF目錄361092 > NCP1522ASNT1G (ON SEMICONDUCTOR) 3.0 MHz, 600 mA, High−Efficiency, Low Quiescent Current, Adjustable Output Voltage Step−Down Converter PDF資料下載
參數資料
| 型號： | NCP1522ASNT1G |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | 3.0 MHz, 600 mA, High−Efficiency, Low Quiescent Current, Adjustable Output Voltage Step−Down Converter |
| 中文描述： | 1.2 A SWITCHING REGULATOR, 3600 kHz SWITCHING FREQ-MAX, PDSO5 |
| 封裝： | LEAD FREE, TSOP-5 |
| 文件頁數： | 10/17頁 |
| 文件大小： | 166K |
| 代理商： | NCP1522ASNT1G |
NCP1522
http://onsemi.com
10
CyclebyCycle Current Limitation
From the block diagram (Figure 3), an I
LIM
comparator
is used to realize cyclebycycle current limit protection.
The comparator compares the LX pin voltage with the
reference voltage, which is biased by a constant current. If
the inductor current reaches the limit, the I
LIM
comparator
detects the LX voltage falling below the reference voltage
and releases the signal to turn off the switch Q1. The
cyclebycycle current limit is set at 1200 mA (nom).
Short Circuit Protection
When the output is shorted to ground, the device limits
the inductor current. The dutycycle is minimum and the
consumption on the input line is 300 mA (Typ). When the
short circuit condition is removed, the device returns to the
normal mode of operation.
SoftStart
The NCP1522 uses softstart (300 s Typ) to limit the
inrush current when the device is initially enabled.
Softstart is implemented by gradually increasing the
reference voltage until it reaches the full reference voltage.
During startup, a pulsed current source charges the internal
softstart capacitor to provide gradually increasing
reference voltage. When the voltage across the capacitor
ramps up to the nominal reference voltage, the pulsed
current source will be switched off and the reference
voltage will switch to the regular reference voltage.
Shutdown Mode
When the EN pin has a voltage applied of less than 0.4 V,
the NCP1522 will be disabled. In shutdown mode, the
internal reference, oscillator and most of the control
circuitries are turned off. Therefore, the typical current
consumption will be 0.3 A (typical value). Applying a
voltage above 1.2 V to EN pin will enable the device for
normal operation. The device will go through softstart to
normal operation, however, the EN pin should be tied low
while the input voltage on V
IN
pin is rising up.
Thermal Shutdown
Internal Thermal Shutdown circuitry is provided to
protect the integrated circuit in the event that the maximum
junction temperature is exceeded. If the junction
temperature exceeds 160 C, the device shuts down. In this
mode switch Q1 and Q2 and the control circuits are all
turned off. The device restarts in softstart after the
temperature drops below 135 C. This feature is provided
to prevent catastrophic failures from accidental device
overheating and it is not intended as a substitute for proper
heatsinking.
Low Dropout Operation
The NCP1522 offers a low input to output voltage
difference. The NCP1522 can operate at 100% duty cycle.
In this mode the PMOS (Q1) switches completely on.
The minimum input voltage to maintain regulation can
be calculated as:
VIN(min)
VOUT(max)
(IOUT
(RDS(on)
(eq. 1)
RINDUCTOR))
V
OUT
: Output Voltage (Volts)
I
OUT
: Max Output Current
R
DS(on)
: PChannel Switch R
DS(on)
R
INDUCTOR
: Inductor Resistance (DCR)
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1523 | 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans |
| NCP1560 | Full Featured Voltage Mode PWM Controller(全性能電壓模式PWM控制器) |
| NCP1560HDR2 | Quadruple Differential Line Receiver With 3-State Outputs 16-PDIP 0 to 70 |
| NCP1562A | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Clamp/Reset PWM控制器) |
| NCP1562B | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Active Clamp/Reset PWM控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1522BMUTBG | 功能描述:直流/直流開關轉換器 STEP DWN DCDC CNVRTR 3.0MHz 600mA RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1522BSNT1G | 功能描述:直流/直流開關轉換器 STEP DWN DCDC CNVRTR 3.0MHz 600mA RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1522BUEVB | 功能描述:電源管理IC開發工具 NCP1522 EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1522BUGEVB | 功能描述:電源管理IC開發工具 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1523BFCT2G | 功能描述:直流/直流開關轉換器 FORCED PWM NCP1523 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。