- 您現在的位置：買賣IC網 > PDF目錄361092 > NCP1522ASNT1G (ON SEMICONDUCTOR) 3.0 MHz, 600 mA, High−Efficiency, Low Quiescent Current, Adjustable Output Voltage Step−Down Converter PDF資料下載
參數資料
| 型號： | NCP1522ASNT1G |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | 3.0 MHz, 600 mA, High−Efficiency, Low Quiescent Current, Adjustable Output Voltage Step−Down Converter |
| 中文描述： | 1.2 A SWITCHING REGULATOR, 3600 kHz SWITCHING FREQ-MAX, PDSO5 |
| 封裝： | LEAD FREE, TSOP-5 |
| 文件頁數： | 9/17頁 |
| 文件大小： | 166K |
| 代理商： | NCP1522ASNT1G |
NCP1522
http://onsemi.com
9
OPERATION DESCRIPTION
Overview
The NCP1522 uses a constant frequency, voltage mode
stepdown architecture. Both the main (PChannel
MOSFET) and synchronous (NChannel MOSFET)
switches are internal.
It delivers a constant voltage from either a single LiIon
or three cell NiMH/NiCd battery to portable devices such
as cell phones and PDA. The output voltage is set by
external resistor divider. The NCP1522 sources at least
600 mA depending on external components chosen.
The NCP1522 works with two modes of operation; PWM
depending on the current required. The device operates in
PWM/PFM mode at load currents of approximately 80 mA
or higher, having voltage tolerance of
efficiency or better. Lighter load currents cause the device
to automatically switch into PFM mode for reduced current
consumption (I
Q
= 60 A typ) and extended battery life.
Additional features include softstart, undervoltage
protection, current overload protection, and thermal
shutdown protection. As shown in Figure 1, only six
external components are required for implementation. The
part uses an internal reference voltage of 0.6 V. It is
recommended to keep the part in shutdown until the input
voltage is 2.7 V or higher.
3% with 90%
PWM Operating Mode
In this mode, the output voltage of the NCP1522 is
regulated by modulating the ontime pulse width of the
main switch Q1 at a fixed frequency of 3.0 MHz. The
switching of the PMOS Q1 is controlled by a flipflop
driven by the internal oscillator and a comparator that
compares the error signal from an error amplifier with the
PWM ramp. At the beginning of each cycle, the main
switch Q1 is turned ON by the rising edge of the internal
oscillator clock. The inductor current ramps up until the
sum of the current sense signal and compensation ramp
becomes higher than the error voltage amplifier. Once this
has occurred, the PWM comparator resets the flipflop, Q1
is turned OFF and the synchronous switch Q2 is turned ON.
Q2 replaces the external Schottky diode to reduce the
conduction loss and improve the efficiency. To avoid
overall power loss, a certain amount of dead time is
introduced to ensure Q1 is completely turned OFF before
Q2 is being turned ON.
Figure 23. PWM Switching Waveform
(V
in
= 3.6 V, V
out
= 1.8 V, I
out
= 300 mA)
125 ns/div
PFM Operating Mode
Under light load conditions, the NCP1522 enters in low
current PFM mode operation to reduce power
consumption. The output regulation is implemented by
pulse frequency modulation. If the output voltage drops
below the threshold of PFM comparator (typically
Vnom2%), a new cycle will be initiated by the PFM
comparator to turn on the switch Q1. Q1 remains ON until
the peak inductor current reaches 200 mA (nom). Then
I
LIM
comparator goes high to switch off Q1. After a short
dead time delay, switch rectifier Q2 is turned ON. The
negative current detector (NCD) will detect when the
inductor current drops below zero and sends the signal to
turn off Q2. The output voltage continues to decrease
through discharging the output capacitor. When the output
voltage falls below the threshold of the PFM comparator,
a new cycle starts immediately.
Figure 24. PFM Mode Switching Waveform
(V
in
= 3.6 V, V
out
= 1.8 V, I
out
= 30 mA)
5 s/div
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1523 | 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans |
| NCP1560 | Full Featured Voltage Mode PWM Controller(全性能電壓模式PWM控制器) |
| NCP1560HDR2 | Quadruple Differential Line Receiver With 3-State Outputs 16-PDIP 0 to 70 |
| NCP1562A | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Clamp/Reset PWM控制器) |
| NCP1562B | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Active Clamp/Reset PWM控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1522BMUTBG | 功能描述:直流/直流開關轉換器 STEP DWN DCDC CNVRTR 3.0MHz 600mA RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1522BSNT1G | 功能描述:直流/直流開關轉換器 STEP DWN DCDC CNVRTR 3.0MHz 600mA RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1522BUEVB | 功能描述:電源管理IC開發工具 NCP1522 EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1522BUGEVB | 功能描述:電源管理IC開發工具 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1523BFCT2G | 功能描述:直流/直流開關轉換器 FORCED PWM NCP1523 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。