- 您現在的位置：買賣IC網 > PDF目錄361092 > NCP1523 (Texas Instruments, Inc.) 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans PDF資料下載
參數資料
| 型號： | NCP1523 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans |
| 中文描述： | 6甲，2.2 V至5.5 V輸入，非隔離，寬輸出，可調電源模塊的TurboTrans |
| 文件頁數： | 11/35頁 |
| 文件大小： | 1128K |
| 代理商： | NCP1523 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
www.ti.com
APPLICATION INFORMATION
ADJUSTING THE OUTPUT VOLTAGE
The V
O
Adjust control (pin 7) sets the output voltage of the PTH04T230/231W. The adjustment range of the
PTH04T230/231W is 0.69 V to 3.6 V. The adjustment method requires the addition of a single external resistor,
R
, that must be connected directly between the V
Adjust and the –Sense pins.
Table 1
gives the standard
value of the external resistor for a number of standard voltages, along with the actual output voltage that this
resistance value provides.
R
SET
10 k
0.69
V
O
0.69
1.43 k
(1)
UDG06043
R
SET
1%
0.05 W
V
O
+Sense
Sense
VoAdj
GND
3
4
5
6
7
+Sense
Sense
GND
V
O
PTH04T230/231W
PTH04T230W, PTH04T231W
SLTS271A–SEPTEMBER 2006–REVISED OCTOBER 2006
For other output voltages, the value of the required resistor can either be calculated using the following formula,
or simply selected from the range of values given in
Table 2
.
Figure 9
shows the placement of the required
resistor.
Table 1. Preferred Values of R
SET
for Standard Output Voltages
R
SET
(Standard Value) (k
)
3.3
(1)
1.21
2.5
(1)
2.37
1.8
(1)
4.75
1.5
(1)
6.98
1.2
12.1
1.0
20.5
0.7
681
V
O
(Standard) (V)
V
O
(Actual) (V)
3.304
2.506
1.807
1.510
1.200
1.004
0.700
(1)
The minimum input voltage is 2.2 V or (V
O
+ 0.5) V, whichever is greater.
(1)
R
SET
:
Use a 0.05 W resistor with a tolerance of 1% and temperature stability of 100 ppm/
°
C (or better). Connect the
resistor directly between pins 7 and 6, as close to the regulator as possible, using dedicated PCB traces.
Never connect capacitors from V
O
Adjust to either GND, V
O
, or +Sense. Any capacitance added to the V
O
Adjust pin
affects the stability of the regulator.
Figure 9. V
O
Adjust Resistor Placement
(2)
11
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1560 | Full Featured Voltage Mode PWM Controller(全性能電壓模式PWM控制器) |
| NCP1560HDR2 | Quadruple Differential Line Receiver With 3-State Outputs 16-PDIP 0 to 70 |
| NCP1562A | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Clamp/Reset PWM控制器) |
| NCP1562B | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Active Clamp/Reset PWM控制器) |
| NCP1729 | Switched Capacitor Voltage Inverter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1523BFCT2G | 功能描述:直流/直流開關轉換器 FORCED PWM NCP1523 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1523BGEVB | 功能描述:電源管理IC開發工具 NCP1523B EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1523FCT2G | 功能描述:直流/直流開關轉換器 UBUMP DCDC RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1526EVB | 功能描述:電源管理IC開發工具 NCP1526 EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1526MUTXG | 功能描述:直流/直流開關轉換器 BUCK REG AND LDO RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。