- 您現在的位置：買賣IC網 > PDF目錄361092 > NCP1523 (Texas Instruments, Inc.) 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans PDF資料下載
參數資料
| 型號： | NCP1523 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans |
| 中文描述： | 6甲，2.2 V至5.5 V輸入，非隔離，寬輸出，可調電源模塊的TurboTrans |
| 文件頁數： | 17/35頁 |
| 文件大小： | 1128K |
| 代理商： | NCP1523 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
www.ti.com
TURBOTRANS
TurboTrans Technology
TurboTrans Selection
PTH04T230W, PTH04T231W
SLTS271A–SEPTEMBER 2006–REVISED OCTOBER 2006
TurboTrans technology is a feature introduced in the T2 generation of the PTH/PTV family of power modules.
TurboTrans optimizes the transient response of the regulator with added external capacitance using a single
external resistor. Benefits of this technology include reduced output capacitance, minimized output voltage
deviation following a load transient, and enhanced stability when using ultra-low ESR output capacitors. The
amount of output capacitance required to meet a target output voltage deviation is reduced with TurboTrans
activated. Likewise, for a given amount of output capacitance, with TurboTrans engaged, the amplitude of the
voltage deviation following a load transient is reduced. Applications requiring tight transient voltage tolerances
and minimized capacitor footprint area benefits greatly from this technology.
Using TurboTrans requires connecting a resistor, R
, between the +Sense pin (pin 5) and the TurboTrans pin
(pin 8). The value of the resistor directly corresponds to the amount of output capacitance required. All T2
products require a minimum value of output capacitance whether or not TurboTrans is used. For the
PTH04T230W, the minimum required capacitance is 200
μ
F ceramic. When using TurboTrans, capacitors with a
capacitance
×
ESR product below 10,000
μ
F
×
m
are required. (Multiply the capacitance (in
μ
F) by the ESR (in
m
) to determine the capacitance
×
ESR product.) See the Capacitor Selection section of the datasheet for a
variety of capacitors that meet this criteria.
Figure 10
shows the amount of output capacitance required to meet a desired transient voltage deviation with
and without TurboTrans for several capacitor types; Type A (e.g. ceramic), Type B (e.g. polymer-tantalum), and
Type C (e.g. OS-CON). To calculate the proper value of R
, first determine the required transient voltage
deviation limits and magnitude of the transient load step. Next, determine what type of output capacitors is used.
(If more than one type of output capacitor is used, select the capacitor type that makes up the majority of the
total output capacitance). Knowing this information, use the chart in
Figure 10
that corresponds to the capacitor
type selected. To use the chart, begin by dividing the maximum voltage deviation limit (in mV) by the magnitude
of the load step (in Amps). This gives a mV/A value. Find this value on the Y-axis of the appropriate chart. Read
across the graph to the
'With TurboTrans
' plot. From this point, read down to the X-axis which lists the minimum
required capacitance, C
O
, to meet that transient voltage deviation. The required R
TT
resistor value can then be
calculated using the equation or selected from the TurboTrans table. The TurboTrans tables include both the
required output capacitance and the corresponding R
values to meet several values of transient voltage
deviation for 25% (1.5 A), 50% (3 A), and 75% (4.5 A) output load steps.
The chart can also be used to determine the achievable transient voltage deviation for a given amount of output
capacitance. Selecting the amount of output capacitance along the X-axis, reading up to the
'With TurboTrans'
curve, and then over to the Y-axis, gives the transient voltage deviation limit for that value of output capacitance.
The required R
TT
resistor value can be calculated using the equation or selected from the TurboTrans table.
As an example, consider a 5-V application requiring a 45 mV deviation during a 3-A, 50% load transient. A
majority of 330
μ
F, 10 m
ouput capacitors are used. Use the Type B capacitor chart,
Figure 11
. Dividing 45 mV
by 3 A gives 15 mV/A transient voltage deviation per amp of transient load step. Select 15 mV/A on the Y-axis
and read across to the
'With TurboTrans
' plot. Following this point down to the X-axis gives us a minimum
required output capacitance of approximately 820
μ
F. The required R
TT
resistor value for 820
μ
F can then be
calculated or selected from
Table 5
. The required R
TT
resistor is approximately 6.19 k
.
To see the benefit of TurboTrans, follow the 15 mV/A marking across to the
'Without TurboTrans
' plot. Following
that point down shows that you would need a minimum of 2700
μ
F of output capacitance to meet the same
transient deviation limit. This is the benefit of TurboTrans. A typical TurboTrans schematic is shown in
Figure 16
.
17
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1560 | Full Featured Voltage Mode PWM Controller(全性能電壓模式PWM控制器) |
| NCP1560HDR2 | Quadruple Differential Line Receiver With 3-State Outputs 16-PDIP 0 to 70 |
| NCP1562A | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Clamp/Reset PWM控制器) |
| NCP1562B | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Active Clamp/Reset PWM控制器) |
| NCP1729 | Switched Capacitor Voltage Inverter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1523BFCT2G | 功能描述:直流/直流開關轉換器 FORCED PWM NCP1523 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1523BGEVB | 功能描述:電源管理IC開發工具 NCP1523B EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1523FCT2G | 功能描述:直流/直流開關轉換器 UBUMP DCDC RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1526EVB | 功能描述:電源管理IC開發工具 NCP1526 EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1526MUTXG | 功能描述:直流/直流開關轉換器 BUCK REG AND LDO RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。