欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: OCB350L187Z
廠商: TT Electronics/Optek Technology
文件頁數: 6/8頁
文件大小: 862K
描述: BOARD CALIBR CIRCUIT OPB350L187
標準包裝: 1
系列: *
產品目錄頁面: 2788 (CN2011-ZH PDF)
配用: 365-1490-ND - BOARD CALIBR CIRCUIT OPB350L062
其它名稱: 365-1531
OPTEK Technology Inc.  1645 Wallace Drive, Carrollton, Texas 75006 
Phone: (972) 323-2200 or (800) 341-4747      FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue E 11/2011
Page 6 of 8
Tube Liquid Sensor
OPB350 / OCB350 Series
(Calibration Circuit Available)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Calibration Circuit theory of operation:
 
The OCB350 series is designed to minimize the change of optical devices due to manufacturing variance. With the calibration
circuit, the design engineer can narrow the initial output state providing a device that will operate the same for years with the
same startup state thus enhancing the reliability and consistence of the system. Degradation of the LED or phototransistor is
compensated for each time the system is calibrated allowing the system to provide a known, consistent output level resulting
in years of consistent quality. The OCB350 series are designed to maintain the calibrated setting even if power is lost. This
allows faster startup without the need for calibration every time the device is initiated. The designer can initiate the calibration
procedure at any time by momentarily grounding J1-Pin-4 (green wire). This allows the device to be remotely calibrated then
mounted in the equipment.
 
The PCBoard has a set of shorting pins allowing the user to change the phototransistor load resistor. By arranging the
shorting bar to the appropriate location (see table), the load resistance can be changed from approximately 2.5K to 27 K ?
Increasing the load resistor increases the sensitivity of the device.
 
When the Calibrate pin (#4) is momentarily grounded, the system begins its calibration process and raises the current
through the LED, from 0 mA to 14 mA, until the phototransistor reaches the preset calibration point. A green calibration light
will blink during the initiation and will stop when the preset phototransistor output level is reached. At this time, the LED
drive current is locked and maintained until Reset/Clear pin is momentarily grounded. If for some reason, the LED drive
current reaches the maximum allowable value, a RED warning light will be turned on. During the calibration process, remote
monitoring of J1-Pin3 allows the designer to ensure the system is calibrated (this output should be at the preset calibrated
output level when the calibration procedure is completed). The phototransistor load resistor may need to be adjusted to allow
the system to calibrate properly.
 
After the calibration process is complete, the device is ready for acknowledgement of a change in the signal. The design
engineer can monitor either the Analog Output (J1-Pin 5) or Logical Output (J1-Pin 2 or J1-Pin 3).
 
The Logical output will change state once the preset optical light condition is reached. The Logic Out A switches when the
optical signal increases above approximately 2/3 of V
CC
 while Logic Out B switches when the optical signal decreases
below approximately 1/3 of V
CC
.
 
As with all optical devices, the switching condition is consistent with the phototransistor receiving a preset light level. This
switching position and light level may vary dependent on several possible factors such as:
"    Ambient light variation ((reduced or eliminated with periodic recalibration)
"    LED and phototransistor pair degradation (eliminated with periodic recalibration)
"    Contamination in front of either the LED or phototransistor (reduced or eliminated with periodic cleaning)
"    System power variation (reduced or eliminated with periodic recalibration)
"    Temperature changes (reduced or eliminated with periodic recalibration)
相關PDF資料
PDF描述
OMB.242.08F21 OMNI OUTDOOR ANTENNA
OMNILOG90200 ANTENNA ISOTRP 700MHZ-2.5GHZ RAD
OPR5011 COMPARATOR OPTICAL 3 CHAN SMD
P522304 CELL ANTENNA 5-BAND 35X9X3.2MM
P522306 RF ANT PRESTTA PENTA-BAND U.FL
相關代理商/技術參數
參數描述
OCB350L250Z 功能描述:光學開關(透射型,光電晶體管輸出) Calibration Circuit With OPB350L250 RoHS:否 制造商:Omron Electronics 輸出設備:Phototransistor 槽寬:3.4 mm 光圈寬度:0.5 mm 集電極—發射極最大電壓 VCEO:30 V 最大集電極電流:20 mA 正向電流: 安裝風格:Through Hole 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝:
OCB-375 制造商:Heyco Products Inc 功能描述:
OCB-500 制造商:Heyco Products Inc 功能描述:
OCB-562 制造商:Heyco Products Inc 功能描述:
OCB-625 制造商:Heyco Products Inc 功能描述:
主站蜘蛛池模板: 阳高县| 桂林市| 株洲县| 如东县| 马关县| 永登县| 芒康县| 遂溪县| 普陀区| 南和县| 巴里| 湘乡市| 太康县| 彰化市| 昭通市| 凤冈县| 庆元县| 岑巩县| 南木林县| 安陆市| 苏尼特右旗| 永安市| 日土县| 繁峙县| 舟山市| 清镇市| 兴文县| 宝应县| 商城县| 揭西县| 丹阳市| 浏阳市| 迭部县| 同德县| 玉门市| 吉木萨尔县| 河池市| 威海市| 铜梁县| 宜君县| 阳信县|