欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： PCD5013
廠商： NXP Semiconductors N.V.
英文描述： FLEX roaming decoder II
中文描述： FleX創建漫游解碼器二
文件頁數： 33/76頁
文件大小： 270K
代理商： PCD5013
1999 Apr 12
33
Philips Semiconductors
Product specification
FLEX
roaming decoder II
PCD5013
8.5.8
R
ECEIVER SHUT
-
DOWN SEQUENCE
The PCD5013 allows up to 3 steps associated with
shutting down the receiver. When the PCD5013 decides to
turn off the receiver, the first shut-down setting, if enabled,
is applied to the receiver control lines for the
corresponding shut-down time. At the end of the last used
shut-down time, the receiver off setting is applied to the
receiver control lines. If the first shut-down setting is not
enabled, the PCD5013 switches directly from the
receiver on to the receiver off setting.
Figure 15 shows the receiver shut-down sequence when
all shut-down settings are enabled. If the receiver is on or
being warmed up when the decoder is turned off (by
clearing the ON bit in the control packet), the PCD5013
immediately executes the receiver shut-down sequence.
If the PCD5013 is executing the shut-down sequence
when turned on (with the ON bit in the control packet set)
the PCD5013 completes the shut-down sequence before
starting the warm-up sequence.
8.5.8.1
Receiver shut-down setting packets
(ID = 1AH to 1BH)
SE:
step enable (Table 28). The receiver setting is
enabled when the bit is set. If the bit is cleared then that
step in the receiver shut-down sequence is disabled and
all following steps are ignored. Value after reset = 0.
LBC:
low battery check (Table 28). If this bit is set, the
PCD5013 checks the status of the LOBAT port just before
leaving this receiver shut-down state. Value after
reset = 0.
CLS:
control line setting (Table 28). This is the value to be
output on the receiver control lines (S0 to S7) for this
receiver shut-down state. Value after reset = 0.
ST:
step time (Table 28). This sets the duration time for
receiver shut-down, until the next receiver state.
The setting is in steps of 625
μ
s. Valid values are
625
μ
s (ST = 01H) to 39.375 ms (ST = 3FH). Value after
reset = 01H.
s:
setting number, see Tables 27 and 28 for the s names
and values and location in the receiver shut-down packet.
Table 27
s names and values
s
SETTING NAME
0
1
shut-down 1
shut-down 2
Table 28
Receiver shut-down stages
BYTE
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
3
2
1
0
0
0
0
0
0
1
0
1
0
0
1
0
s
0
SE
CLS
7
0
LBC
CLS
3
ST
3
CLS
6
0
CLS
5
ST
5
CLS
4
ST
4
CLS
2
ST
2
CLS
1
ST
1
CLS
0
ST
0
Fig.15 Receiver shut-down sequence.
handbook, full pagewidth
MGK267
receiver
control
line setting
shut down
time 1
shut down
setting 1
shut down
time 2
shut down
setting 2
possible
LOBAT
check
off
possible
LOBAT
check
possible
LOBAT
check
1600 sps or 3200 sps
sync or data setting
相關PDF資料
PDF描述
PCD5013H FLEX roaming decoder II
PCD5032 ADPCM CODEC for digital cordless telephones
PCD5032H ADPCM CODEC for digital cordless telephones
PCD5032T ADPCM CODEC for digital cordless telephones
PCD5041 DECT burst mode controller
相關代理商/技術參數
參數描述
PCD5013H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:FLEX roaming decoder II
PCD5032 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
PCD5032B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
PCD5032D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
PCD5032H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 永登县| 沙坪坝区| 临泉县| 富蕴县| 莫力| 武山县| 青海省| 青田县| 华池县| 保康县| 寻乌县| 泾源县| 巴彦淖尔市| 青龙| 夹江县| 高密市| 陆良县| 新河县| 确山县| 元朗区| 房产| 嵊州市| 宜春市| 武清区| 汪清县| 临泉县| 和林格尔县| 两当县| 丰都县| 陇川县| 丘北县| 平南县| 顺昌县| 佳木斯市| 伊金霍洛旗| 锡林郭勒盟| 寿阳县| 夏河县| 嘉善县| 眉山市| 台北市|