欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： PCD5013H
廠商： NXP SEMICONDUCTORS
元件分類： 尋呼電路
英文描述： FLEX roaming decoder II
中文描述： TELECOM, PAGING DECODER, PQFP32
封裝： 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, SOT-358-1, LQFP-32
文件頁數： 7/76頁
文件大小： 270K
代理商： PCD5013H
1999 Apr 12
7
Philips Semiconductors
Product specification
FLEX
roaming decoder II
PCD5013
8
FUNCTIONAL DESCRIPTION
8.1
General
The PCD5013 simplifies implementation of a FLEX
paging device by interfacing with off-the-shelf components
such as a paging receiver and a microcontroller or
microprocessor (called a host). The PCD5013 is fully
compatible with FLEXstack
software which provides a
complete, platform independent, software driver for the
PCD5013.
The PCD5013 fully supports all aspects of the FLEX
protocol (version G1.9), and can operate in either
single-phase or any-phase mode. The PCD5013 supports
FLEX
dynamic grouping, allowing up to 16 temporary
addresses to be enabled simultaneously. It is also capable
of retrieving real time information from a FLEX
channel.
The PCD5013 connects to any receiver capable of
providing a 2-bit digital signal. The PCD5013 operates the
paging receiver in an efficient power consumption mode.
The PCD5013 has 8 receiver control lines used for
warming up, operating and shutting down a receiver in
stages.
The PCD5013 has the ability to detect a battery-low signal
from an external detector during the receiver control
sequences.
The PCD5013 carries out the following functions:
Synchronises to a FLEX
data stream
Processes received, demodulated information
Performs de-interleaving and error correction
Selects calls addressed to the paging device using up to
16 programmable addresses
Communicates the message information to the host.
The PCD5013 interfaces to a host through a serial
peripheral interface (SPI). The host can then interpret the
message information in an appropriate manner (numeric,
alphanumeric, binary, etc.). This function is provided by
the FLEXstack
software.
When configured to use the internal demodulator, the
PCD5013 connects to a receiver capable of generating a
limited (i.e. 1-bit digitized) 455 or 140 kHz IF signal
(IF frequency automatically detected).
The PCD5013 enables the host to operate in a low-power
mode when monitoring a single channel for message
information. It has a 38.4 kHz clock output (40 kHz
available when using the internal demodulator) capable of
driving other devices, and has a 1-minute timer that offers
low-power support for a real-time clock function on the
host.The host can use receiver control lines which are not
required by the receiver as expansion ports to control other
peripheral devices.
8.2
Clocking, reset and start-up
8.2.1
O
SCILLATOR
The PCD5013 uses an inverting crystal oscillator.
The clock signal for the internal circuitry is derived via an
amplifier from the oscillator input pin EXTAL. Alternatively,
an external clock signal can be fed in at input pin EXTAL.
In this case the internal oscillator can be disabled by
pulling the OSCPD input pin HIGH. This reduces current
consumption and routes EXTAL directly to the internal
clock signal. When using a crystal, an external feedback
resistor and the load capacitances need to be connected
to pins EXTAL and XTAL (Fig.19). See Chapter 14 for the
recommended crystal parameters and the specification of
the oscillator transconductance to guarantee correct
start-up.
The PCD5013 oscillator can operate at either 76.8 kHz or
160 kHz by selecting the appropriate crystal. The choice of
frequency is determined by the setting of the IDE bit in the
configuration packet; see Section 8.4.4.
8.2.2
R
ESET AND START
-
UP CONDITIONS
The PCD5013 is reset by pulling the RESET input LOW.
After releasing the RESET by pulling it HIGH, the
PCD5013 counts 76800 clock cycles (independent of the
oscillator frequency) before pulling READY LOW to
indicate that the decoder is ready for configuration via
the SPI.
See Fig.3 and Chapter 13 for the PCD5013 timing
specifications when power is applied.
See Fig.4 and Chapter 13 for the PCD5013 timing
specifications when it is reset.
After switch-on, the PCD5013 operates in Asynchronous
mode, periodically sampling the channel for incoming
data. As soon as data is detected, the PCD5013 maintains
the receiver on to synchronize to the channel. Once the
pager is synchronized to the channel it enters
Synchronous mode, switching the receiver on only for the
programmed frames.
When the receiver is programmed for Roaming operation,
the PCD5013 sends information which allows the host to
calculate when to switch frequencies in a roaming
network.
相關PDF資料
PDF描述
PCD5032 ADPCM CODEC for digital cordless telephones
PCD5032H ADPCM CODEC for digital cordless telephones
PCD5032T ADPCM CODEC for digital cordless telephones
PCD5041 DECT burst mode controller
PCD5041H DECT burst mode controller
相關代理商/技術參數
參數描述
PCD5032 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
PCD5032B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
PCD5032D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
PCD5032H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
PCD5032T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 墨玉县| 商水县| 金寨县| 新安县| 宜君县| 安徽省| 宣恩县| 综艺| 大冶市| 乌恰县| 封开县| 塘沽区| 朔州市| 蒙山县| 宁明县| 嘉义县| 安福县| 临沂市| 施甸县| 武义县| 正镶白旗| 雅安市| 博兴县| 惠州市| 马关县| 庆阳市| 镇坪县| 白城市| 兰西县| 句容市| 东宁县| 资溪县| 榆社县| 神木县| 明溪县| 榆中县| 枣阳市| 泗阳县| 哈尔滨市| 长宁县| 新乡县|