- 您現在的位置：買賣IC網 > PDF目錄382382 > PCF8577CP (NXP SEMICONDUCTORS) LCD direct/duplex driver with I2C-bus interface PDF資料下載
參數資料
| 型號： | PCF8577CP |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 顯示驅動器 |
| 英文描述： | LCD direct/duplex driver with I2C-bus interface |
| 中文描述： | LIQUID CRYSTAL DISPLAY DRIVER, PDIP40 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-40 |
| 文件頁數： | 8/28頁 |
| 文件大?。?/td> | 175K |
| 代理商： | PCF8577CP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
1998 Jul 30
8
Philips Semiconductors
Product specification
LCD direct/duplex driver with
I
2
C-bus interface
PCF8577C
6.7
Power-on reset
At power-on reset the PCF8577C resets to a defined
starting condition as follows:
1.
Both backplane outputs are set to V
SS
in master mode;
to 3-state in cascade mode
2.
All segment outputs are set to V
SS
3.
The segment byte registers and control register are
cleared
4.
The I
2
C-bus interface is initialized.
6.8
Slave address
The PCF8577C slave address is shown in Fig.6.
Before any data is transmitted on the I
2
C-bus, the device
which should respond is addressed first. The addressing is
always done with the first byte transmitted after the start
procedure.
Fig.6 PCF8577C slave address.
0 1 1 1 0 1 0 0
S
A
SLAVE ADDRESS
MGA731
6.9
I
2
C-bus protocol
The PCF8577C I
2
C-bus protocol is shown in Fig.7.
The PCF8577C is a slave receiver and has a fixed slave
address (see Fig.6). All PCF8577Cs with the same slave
address acknowledge the slave address in parallel.
The second byte is always the control byte and is loaded
into the control register of each PCF8577C connected to
the I
2
C-bus. All addressed devices acknowledge the
control byte. Subsequent data bytes are loaded into the
segment registers of the selected device. Any number of
data bytes may be loaded in one transfer and in an
expanded system rollover of the SBV from 111 111 to
000 000 is allowed. If a stop (P) condition is given after the
control byte acknowledge the segment data will remain
unchanged. This allows the BANK bit to be toggled without
changing the segment register contents. During loading of
segment data only the selected PCF8577C gives an
acknowledge. Loading is terminated by generating a stop
(P) condition.
Fig.7 I
2
C-bus protocol.
S
A
SLAVE ADDRESS
A
A
SEGMENT DATA
P
acknowledge by
all PCF8577C
R/W
auto increment
segment byte vector
MGA732
0
M
B
SEGMENT
BYTE VECTOR
acknowledge by
all PCF8577C
acknowledge by
selected PCF8577C only
msb
lsb
n bytes
control byte
相關PDF資料 |
PDF描述 |
|---|---|
| PCF8591 | 8-bit A/D and D/A converter |
| PCA8591 | 8-bit A/D and D/A converter |
| PCA8591P | 8-bit A/D and D/A converter |
| PCA8591T | 8-bit A/D and D/A converter |
| PCF8598C-2P02 | 1024 ⅴ 8-bit CMOS EEPROM with I2C-bus interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF8577CP/F3,112 | 功能描述:LCD 驅動器 LCD DRIVER 32/64SEG RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| PCF8577CP/F3112 | 制造商:NXP Semiconductors 功能描述:LCD DRIVER 32/64 SEGMENT 8577 DIP |
| PCF8577CP/FZ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-LCD DRIVER |
| PCF8577CPN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Display Driver |
| PCF8577CT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD direct/duplex driver with I2C-bus interface |
發布緊急采購，3分鐘左右您將得到回復。