欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD301V-20JM
廠商: 意法半導體
英文描述: 5015 RR 3#16S PIN RECPT
中文描述: 低成本現場可編程微控制器外圍設備
文件頁數: 25/85頁
文件大小: 691K
代理商: PSD301V-20JM
PSD3XX Famly
22
12.0
Control Signals
Consult your MCU data sheet to determine which control signals your MCU generates, and
how they operate. This section is intended to show which control signals should be
connected to what pins on the PSD3XX. You will then use PSDsoft to configure the
PSD3XX, based on the combination of control signals that your MCU outputs, for example
RD, WR, and PSEN.
The PSD3XX is compatible with the following control signals:
ALE or AS (polarity is programmable)
WR or R/W
RD/E or RD/E/DS (DS for non-3X1 devices only)
BHE or PSEN
A19/CSI
RESET (polarity is programmable except on low voltage versions with the V suffix).
12.1 ALE or AS
Connect the ALE or AS signal from your MCU to this pin where applicable, and program
the polarity using PSDsoft. The trailing edge (when the signal goes inactive) of ALE or AS
latches the address on any pins that have an address input. If you are using a
non-multiplexed-bus MCU that does not output an ALE or AS signal, this pin can be used
for a generic input to the PAD.
Note: if your data is multiplexed with address lines other
than A0-A7
, connect your address pins to AD0/A0-AD15/A15, and connect your data to
Port A (and Port B where applicable), and connect the ALE/AS signal to this pin.
12.2 WR or R/W
Your MCU should output a stand-alone write signal (WR) or a multiplexed read/write signal
(R/W). In either case, the signal should be connected to this pin.
12.3 RD/E/DS (DS option not available on 3X1 devices)
Your MCU should output any one of RD, E (clock), or DS. In any case, connect the
appropriate signal to this pin.
12.4 BHE or PSEN
J
If your MCU does not output either of these signals, tie this pin to Vcc
(through a series resistor), and skip to the next signal.
J
If you use an 8-bit 8031 compatible MCU that outputs a separate signal when
accessing program space, such as PSEN, connect it to this pin. You would then use
PSDsoft to configure the EPROM in the PSD3XX to respond to PSEN only or PSEN
and RD. If you have an 8031 compatible MCU, refer to the “Program/Data Space and
the 8031” section for further information.
J
If you are using a 16-bit MCU, connect the BHE (or similar signal) output to this pin.
BHE enables accessing of the upper byte of the data bus. See Table 6 for information
on how this signal is used in conjunction with the A0 address line.
BHE
A
0
0
1
0
1
Operation
0
0
1
1
Whole Word
Upper Byte From/To Odd Address
Lower Byte From/To Even Address
None
Table 6. Truth Table for BHE and Address Bit A0 (16-bit MCUs only)
相關PDF資料
PDF描述
PSD301V-25J 5015 RR 6#16S SKT RECP
PSD301V-25JI 5015 RR 3#16S SKT RECPT
PSD301V-25JM 5015 RR 3#16S SKT RECPT
PSD301V-70J Low Cost Field Programmable Microcontroller Peripherals
PSD301V-70JI Low Cost Field Programmable Microcontroller Peripherals
相關代理商/技術參數
參數描述
PSD301V-25J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD301V-25JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD301V-25JM 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD301V-70J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD301V-70JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
主站蜘蛛池模板: 二连浩特市| 濮阳市| 宣城市| 建德市| 宁海县| 广河县| 怀化市| 永丰县| 越西县| 北辰区| 黑河市| 和平县| 那坡县| 庄浪县| 辽宁省| 固镇县| 驻马店市| 清徐县| 富源县| 高碑店市| 封开县| 甘泉县| 嘉兴市| 屏南县| 齐齐哈尔市| 双峰县| 重庆市| 泸定县| 缙云县| 镇原县| 利辛县| 镇远县| 东丽区| 紫金县| 八宿县| 东宁县| 安康市| 米脂县| 尉犁县| 巴彦淖尔市| 克东县|