- 您現在的位置：買賣IC網 > Datasheet目錄46 > QPI-8LZ-01 (Vicor Corporation)IC HOT SWAP EMI FILTER 16LGA Datasheet資料下載
參數資料
| 型號： | QPI-8LZ-01 |
| 廠商： | Vicor Corporation |
| 文件頁數： | 9/17頁 |
| 文件大小： | 1498K |
| 描述： | IC HOT SWAP EMI FILTER 16LGA |
| 標準包裝： | 20 |
| 系列： | Picor®, QUIETPOWER® |
| 類型： | 熱交換開關 |
| 應用： | AdvancedTCA |
| 內部開關： | 是 |
| 電流限制： | 6A |
| 電源電壓： | 36 V ~ 76 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | * |
| 供應商設備封裝： | * |
| 包裝： | 管件 |
| 其它名稱： | 1102-1092-5 |
C
E
Picor Corporation ?picorpower.com
QPI-8
Rev 1.5, Page 9 of 17
QPI-8
QUIETPOWER
?/DIV>
QPI-8 Timing Waveforms
The waveforms in Figure 17 are the typical start-up
waveforms that would be seen in a system where two current
pulses are required to completely charge the bulk
capacitance to the bus voltage. The GATE waveform is an
internal signal and cannot be measured externally; it is shown
only for reference.
Once VIN is established and the UV and OV thresholds are
satisfied, the internal FETs gate will start to get driven high
after a 15ms delay. This delay allows for insertion de-
bouncing. As the FET turns on and allows the passing of
current the magnitude of the current is monitored. Once it
reaches the 6A circuit breaker threshold an internal fault
timer is started and the current is limited to a 12A maximum
value. If the current does not drop to a value below the 6A
circuit breaker limit before the fault timer ends then the gate
is shut off and remains off for about 95ms. After this time
the gate is again turned on and current is allowed to pass.
Once the current is below the circuit breaker limit, the FET is
fully turned on to its minimum r
ds
value and the Powergood
pin is released (open drain).
The change in voltage across VSW is dependent upon the
value of the bulk capacitance that the QPI-8 is charging. The
circuit breaker fault time is 300us when the voltage on VSW is
greater than 40V, referenced to BUS-; or if there is no voltage
change across VSW during the 12A current pulse, indicating a
short across the bulk capacitor. Once below the 40V limit,
and a decreasing voltage across VSW, the fault time is
increased to 1.2ms to charge the bulk capacitors faster.
The timing waveforms for an OV (Over-voltage) and UV
(Under-voltage) events are shown in Figure 18. After the
initial start-up delay, the internal FETs gate is turned on.
Once its gate-to-source voltage reaches 8V it releases the
PWRGD pin and allows it to get pulled up to VIN.
In the event of an OV fault, the QPI-8 will turn off its internal
FET and it will remain off until the OV fault is cleared. Once
cleared, the gate immediately starts to turn back on. With an
UV fault, the FET is again turned off, but the gate is not
turned back on until 15ms after the UV fault has been
cleared.
Figure 17 - QPI-8 current fault timing diagram.
相關PDF資料 |
PDF描述 |
|---|---|
| SA56004HD,118 | IC TEMP SENSOR DIGITAL 8SOIC |
| SC2463TSTRT | IC REG QD BCK/LINEAR 28TSSOP |
| SC338AIMSTRT | IC REG CTRLR DUAL POS ADJ 10MSOP |
| SC402BMLTRT | IC REG DL BCK/LINEAR SYNC 32MLPQ |
| SC403MLTRT | IC REG DL BCK/LINEAR SYNC 32MLPQ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QPI-9 | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:Hot-Swap SiP With VI Chip EMI Filter |
| QPI-9-CB1 | 制造商:Vicor Corporation 功能描述:QPI-9LZ Filter w/ Hot-Swap Carrier Board for 24 V VI Chip "-CB" Boards up to 6A |
| QPI-9L | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:VI Chip Input EMI Filters |
| QPI-9LZ | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:Hot-Swap SiP With VI Chip EMI Filter |
| QPI-9LZ-01 | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:Hot-Swap SiP With VI Chip EMI Filter |
發布緊急采購，3分鐘左右您將得到回復。