- 您現在的位置：買賣IC網 > PDF目錄376314 > romr0008 (SIEMENS AG) MultiMediaCard R0008 8 Mbyte ROM(多媒體卡 R0002 8 Mbyte ROM) PDF資料下載
參數資料
| 型號： | romr0008 |
| 廠商： | SIEMENS AG |
| 英文描述： | MultiMediaCard R0008 8 Mbyte ROM(多媒體卡 R0002 8 Mbyte ROM) |
| 中文描述： | 多媒體R0008 8字節的光盤（多媒體卡R0002 8字節光盤） |
| 文件頁數： | 16/41頁 |
| 文件大?。?/td> | 208K |
| 代理商： | ROMR0008 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
Siemens
Product Manual R0008
Semiconductor Group
17
3.1
6
Communication
All communication between host and cards is controlled by the host (master). The host sends com-
mands and, depending on the command, receives a corresponding response from the selected
card. In this chapter the commands to control the R0008, the card responses and the contents of a
status and error field, included in the responses, are defined.
6.1
Commands
The command set of the MultiMediaCard system is divided into classes corresponding to the type of
card (see also [1]). The R0008 supports the following command classes:
Class 0 is mandatory and supported by all cards. It represents the card identification and initializa-
tion commands, which are intended to handle different cards and card types on the same bus lines.
The Card Command Class (CCC) is coded in the card specific data register of each card, so that
the host knows how to access the card.
There are four kinds of commands defined on the MultiMediaCard bus:
broadcast commands (bc)
sent on CMD line, no response
broadcast commands with response (bcr)
sent on CMD line, response (all cards simultaneously) on CMD line
addressed (point-to-point) commands (ac)
sent on CMD line, response on CMD line
addressed (point-to-point) data transfer commands (adtc)
sent on CMD line, response on CMD line, data transfer on DAT line
The command transmission always starts with the MSB. Each command starts with a start bit and
ends with an CRC command protection field followed by a end bit. The length of each command
frame is fixed to 48 bits (2.4
μ
s @ 20 MHz):
The start bit is always ‘0’ in command frames (sent from host to MultiMediaCard). The host bit is
always ‘1’ for commands. The command field contains the binary coded command number. The
argument depends on the command (see Table 16 and Table 17). The CRC field is defined in
"Chapter 7: Error handling".
1
Cyclic Redundancy Check
Card
Command
Class (CCC)
Class
description
Supported commands
0
1
2
3
4
7
9
10
11
12
13
15
16
17
18
class 0
class 1
class 2
basic
sequential read
block read
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
Table 15: R0008 command classes
0
start bit
1
host
bit 5...bit 0
command
bit 31...bit 0
argument
bit 6...bit 0
CRC
1
1
end bit
相關PDF資料 |
PDF描述 |
|---|---|
| ROS-1000PV | Surface Mount Voltage Controlled Oscillator |
| ROS-1700W | Voltage Controlled Oscillator |
| rosa51 | MultiMediaCard Adapter(多媒體卡適配器) |
| ROSE-1 | FREQUENCY MIXERS |
| ROSE-2 | FREQUENCY MIXERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RONDOREX W22 | 制造商:REX 功能描述:TIME SWITCH 7DAY 2CHANNEL |
| ROPE KIT 15 | 制造商:IMO Precision Controls Ltd 功能描述:ROPE KIT 15M |
| ROPE KIT 15 | 制造商:IMO Precision Controls Ltd 功能描述:ROPE KIT 15M |
| ROPE KIT 30 | 制造商:IMO Precision Controls Ltd 功能描述:ROPE KIT 30M |
| ROPE KIT 30 | 制造商:IMO Precision Controls Ltd 功能描述:ROPE KIT 30M |
發布緊急采購，3分鐘左右您將得到回復。