- 您現在的位置：買賣IC網 > PDF目錄376314 > RS-422 (Electronic Theatre Controls, Inc.) RS-422 AND RS-485 APPLICATION NOTE PDF資料下載
參數資料
| 型號： | RS-422 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | RS-422 AND RS-485 APPLICATION NOTE |
| 中文描述： | RS - 422和RS - 485接口應用筆記 |
| 文件頁數： | 20/44頁 |
| 文件大?。?/td> | 628K |
| 代理商： | RS-422 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
RS-422/485 Application Note
17
B&B Electronics -- PO Box 1040 -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 434-7094
termination resistor to eliminate the DC loading effect. Although this method
eliminates DC loading, capacitor selection is highly dependent on the system
properties. System designers interested in AC termination are encouraged to
read National Semiconductors Application Note 903
2
for further information.
Figure 2.3 illustrates both parallel and AC termination on an RS-485 two-wire
node. In four-wire systems, the termination is placed across the receiver of the
node.
Figure 2.3 Parallel and AC Termination
Biasing an RS-485 Network
When an RS-485 network is in an idle state, all nodes are in listen
(receive) mode. Under this condition there are no active drivers on the
network, all drivers are tristated. Without anything driving the network, the
state of the line is unknown. If the voltage level at the receiver’s A and B
inputs is less than
±
200 mV the logic level at the output of the receivers will
be the value of the last bit received. In order to maintain the proper idle
voltage state, bias resistors must be applied to force the data lines to the idle
condition. Bias resistors are nothing more than a pullup resistor on the data
B line (typically to 5 volts) and a pulldown (to ground) on the data A line.
Figure 2.4 illustrates the placement of bias resistors on a transceiver in a two-
wire configuration. Note that in an RS-485 four-wire configuration, the bias
resistors should be placed on the receiver lines. The value of the bias
resistors is dependent on termination and number of nodes in the system.
The goal is to generate enough DC bias current in the network to maintain a
minimum of 200 mV between the B and A data line. Consider the following
two examples of bias resistor calculation.
2
Refer to Chapter 7 for information on National Semiconductors Application
Notes.
相關PDF資料 |
PDF描述 |
|---|---|
| RS-485 | RS-422 AND RS-485 APPLICATION NOTE |
| RS-MK-X2010 | High Integrity FM Transceiver |
| RS3FS | SDR Cable Assembly; Connector Type A:micro D Ribbon Plug; Connector Type B:micro D Ribbon Plug; Cable Length:2m; No. of Contacts:26; Pitch Spacing:0.8mm RoHS Compliant: Yes |
| RS3FS | Damper Diodes (For TV) |
| RS4FS | SDR Cable Assembly; Connector Type A:micro D Ribbon Plug; Connector Type B:micro D Ribbon Plug; Cable Length:5m; No. of Contacts:26; Pitch Spacing:0.8mm RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RS422-GE1 | 制造商:Carlo Gavazzi 功能描述:CABLE FOR GE90 |
| RS422-MI1 | 制造商:Carlo Gavazzi 功能描述:CABLE FOR MITS MASTER |
| RS422-MI2 | 制造商:Carlo Gavazzi 功能描述:CABLE FOR MITS MASTER |
| RS422-MI3 | 制造商:Carlo Gavazzi 功能描述:CABLE FOR MITS MASTER |
| RS422-OM2 | 制造商:Carlo Gavazzi 功能描述:CABLE FOR OMRON MASTER |
發布緊急采購，3分鐘左右您將得到回復。