欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: S25FL004D0LMAI013
廠商: SPANSION LLC
元件分類: PROM
英文描述: 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
中文描述: 4M X 1 FLASH 3V PROM, PDSO8
封裝: 0.208 INCH, SOP-8
文件頁數: 10/36頁
文件大小: 724K
代理商: S25FL004D0LMAI013
18
S25FL Family (Serial Peripheral Interface) S25FL004D
S25FL004D_00A0 June 28, 2004
Ad va n c e
In f o rm a t i o n
or by driving Write Protect (W#) Low after setting the Status Register Write
Disable (SRWD) bit.
The only way to exit the Hardware Protected Mode (HPM) once entered is to pull
Write Protect (W#) High.
If Write Protect (W#) is permanently tied High, the Hardware Protected Mode
(HPM) can never be activated, and only the Software Protected Mode (SPM),
using the Block Protect (BP2, BP1, BP0) bits of the Status Register, can be used.
Read Data Bytes (READ)
The READ instruction reads the memory at the specified SCK frequency (fSCK)
with a maximum speed of 33 MHz.
The device is first selected by driving Chip Select (CS#) Low. The instruction code
for the Read Data Bytes (READ) instruction is followed by a 3-byte address (A23-
A0), each bit being latched-in during the rising edge of Serial Clock (SCK). Then
the memory contents, at that address, are shifted out on Serial Data Output
(SO), each bit being shifted out, at a frequency fSCK, during the falling edge of
Serial Clock (SCK).
The instruction sequence is shown in Figure 9. The first byte addressed can be at
any location. The address is automatically incremented to the next higher ad-
dress after each byte of data is shifted out. The whole memory can, therefore, be
read with a single Read Data Bytes (READ) instruction. When the highest address
is reached, the address counter rolls over to 00000h, allowing the read sequence
to be continued indefinitely.
The Read Data Bytes (READ) instruction is terminated by driving Chip Select
(CS#) High. Chip Select (CS#) can be driven High at any time during data output.
Any Read Data Bytes (READ) instruction, while a Program, Erase, or Write cycle
is in progress, is rejected without having any effect on the cycle that is in
progress.
Figure 9. Read Data Bytes (READ) Instruction Sequence
Read Data Bytes at Higher Speed (FAST_READ)
The FAST_READ instruction reads the memory at the specified SCK frequency
(fSCK) with a maximum speed of 50 MHz. The device is first selected by driving
Chip Select (CS#) Low. The instruction code for (FAST_READ) instruction is fol-
lowed by a 3-byte address (A23-A0) and a dummy byte, each bit being latched-
in during the rising edge of Serial Clock (SCK). Then the memory contents, at that
Instruction
24-Bit Address
High Impedance
MSB
Data Out 1
Data Out 2
0
31 32 33 34 35 36 37 38 39
30
23
28
10
9
8
7
6
5
4
3
2
1
7 6 5
23 22 21
4
3 2
1 0
3
2
1 0 7
SO
SI
SCK
CS#
相關PDF資料
PDF描述
S25FL004D0LMFI011 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL004D0LMFI013 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL004D0LNFI011 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL004D0LNFI013 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL004D 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
相關代理商/技術參數
參數描述
S25FL004D0LMFI011 制造商:SPANSION 制造商全稱:SPANSION 功能描述:4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL004D0LMFI013 制造商:SPANSION 制造商全稱:SPANSION 功能描述:4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL004D0LNAI011 制造商:SPANSION 制造商全稱:SPANSION 功能描述:4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL004D0LNAI013 制造商:SPANSION 制造商全稱:SPANSION 功能描述:4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL004D0LNFI011 制造商:SPANSION 制造商全稱:SPANSION 功能描述:4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
主站蜘蛛池模板: 庄河市| 青阳县| 新建县| 儋州市| 临海市| 贡山| 永兴县| 昭苏县| 涪陵区| 裕民县| 祁阳县| 胶南市| 新营市| 巫山县| 嵊州市| 嘉黎县| 南平市| 丹东市| 新兴县| 深泽县| 綦江县| 交口县| 湖北省| 唐山市| 二连浩特市| 清丰县| 长阳| 松桃| 郎溪县| 安庆市| 湘阴县| 互助| 乌拉特后旗| 百色市| 方山县| 独山县| 古丈县| 邵阳市| 长丰县| 湟源县| 隆安县|