- 您現在的位置：買賣IC網 > PDF目錄192296 > S29GL032A10TAIR13 (SPANSION LLC) 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY PDF資料下載
參數資料
| 型號： | S29GL032A10TAIR13 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| 中文描述： | 2M X 16 FLASH 3V PROM, 100 ns, PDSO56 |
| 封裝： | MO-142EC, TSOP-56 |
| 文件頁數： | 42/95頁 |
| 文件大?。?/td> | 3585K |
| 代理商： | S29GL032A10TAIR13 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁
May 21, 2008 S29GL-A_00_A12
S29GL-A
47
Data
She e t
7.11
Secured Silicon Sector Flash Memory Region
The Secured Silicon Sector feature provides a Flash memory region that enables permanent part
identification through an Electronic Serial Number (ESN). The Secured Silicon Sector is 256 bytes in length,
and uses a Secured Silicon Sector Indicator Bit (DQ7) to indicate whether or not the Secured Silicon Sector is
locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed,
which prevents cloning of a factory locked part. This ensures the security of the ESN once the product is
shipped to the field.
The factory offers the device with the Secured Silicon Sector either customer lockable (standard shipping
option) or factory locked (contact a Spansion sales representative for ordering information). The customer-
lockable version is shipped with the Secured Silicon Sector unprotected, allowing customers to program the
sector after receiving the device. The customer-lockable version also contains the Secured Silicon Sector
Indicator Bit permanently set to a 0. The factory-locked version is always protected when shipped from the
factory, and has the Secured Silicon Sector Indicator Bit permanently set to a 1. Thus, the Secured Silicon
Sector Indicator Bit prevents customer-lockable devices from being used to replace devices that are factory
locked. Note that the ACC function and unlock bypass modes are not available when the Secured Silicon
Sector is enabled.
The Secured Silicon sector address space in this device is allocated as follows:
The system accesses the Secured Silicon Sector through a command sequence (see Write Protect (WP#)
on page 48). After the system writes the Enter Secured Silicon Sector command sequence, it may read the
Secured Silicon Sector by using the addresses normally occupied by the first sector (SA0). This mode of
operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until
power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending
commands to sector SA0.
7.11.1
Customer Lockable: Secured Silicon Sector NOT Programmed or Protected
At the Factory
Unless otherwise specified, the device is shipped such that the customer may program and protect the 256-
byte Secured Silicon sector.
The system may program the Secured Silicon Sector using the write-buffer, accelerated and/or unlock
bypass methods, in addition to the standard programming command sequence. See Command Definitions
Programming and protecting the Secured Silicon Sector must be used with caution since, once protected,
there is no procedure available for unprotecting the Secured Silicon Sector area and none of the bits in the
Secured Silicon Sector memory space can be modified in any way.
The Secured Silicon Sector area can be protected using one of the following procedures:
Write the three-cycle Enter Secured Silicon Sector Region command sequence, and then follow the in-
system sector protect algorithm as shown in Figure 7.2 on page 46, except that RESET# may be at either
VIH or VID. This allows in-system protection of the Secured Silicon Sector without raising any device pin to
a high voltage. Note that this method is only applicable to the Secured Silicon Sector.
Write the three-cycle Enter Secured Silicon Sector Region command sequence, and then use the alternate
method of sector protection described in Sector Group Protection and Unprotection on page 41.
Once the Secured Silicon Sector is programmed, locked and verified, the system must write the Exit Secured
Silicon Sector Region command sequence to return to reading and writing within the remainder of the array.
Secured Silicon Sector
Address Range
Standard Factory
Locked
ExpressFlash
Factory Locked
Customer
Lockable
x16
x8
000000h–000007h
000000h-00000Fh
ESN
ESN or determined
by customer
Determined by
customer
000008h–00007Fh
000010h-0000FFh
Unavailable
Determined by
customer
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL032A10TAIR20 | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A10TAIR22 | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A11BFIR32 | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A11BFIR33 | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A11BFIR40 | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL032A10TAIR20 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology |
| S29GL032A10TAIR21 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A10TAIR22 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A10TAIR23 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A10TAIR30 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。