欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: S29GL032A11BFIR32
廠商: SPANSION LLC
元件分類: PROM
英文描述: 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
中文描述: 2M X 16 FLASH 3V PROM, 110 ns, PBGA48
封裝: 8.15 X 6.15 MM, LEAD FREE, FBGA-48
文件頁數: 53/95頁
文件大小: 3585K
代理商: S29GL032A11BFIR32
May 21, 2008 S29GL-A_00_A12
S29GL-A
57
Data
She e t
Figure 9.2 Program Operation
Note
See Table 10.2 on page 61 and Table 10.1 on page 62 for program command sequence.
9.5
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from any non-suspended sector. When the Program
Suspend command is written during a programming process, the device halts the program operation within
15
μs maximum (5μs typical) and updates the status bits. Addresses are not required when writing the
Program Suspend command.
After the programming operation is suspended, the system can read array data from any non-suspended
sector. The Program Suspend command may also be issued during a programming operation while an erase
is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend.
If a read is needed from the Secured Silicon Sector area (One-time Program area), then user must use the
proper command sequences to enter and exit this region. Note that the Secured Silicon Sector, autoselect,
and CFI functions are unavailable when a program operation is in progress.
The system may also write the autoselect command sequence when the device is in the Program Suspend
mode. The system can read as many autoselect codes as required. When the device exits the autoselect
mode, the device reverts to the Program Suspend mode, and is ready for another valid operation. See
After the Program Resume command is written, the device reverts to programming. The system can
determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard
program operation. See Write Operation Status on page 63 for more information.
The system must write the Program Resume command (address bits are don’t care) to exit the Program
Suspend mode and continue the programming operation. Further writes of the Resume command are
ignored. Another Program Suspend command can be written after the device resumes programming.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data?
No
Yes
Last Address?
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
相關PDF資料
PDF描述
S29GL032A11BFIR33 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A11BFIR40 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A11BFIR42 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A11BFIR43 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A90TAIR20 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
相關代理商/技術參數
參數描述
S29GL032A11BFIR33 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A11BFIR40 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:Flash - NOR IC
S29GL032A11BFIR41 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A11BFIR42 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A11BFIR43 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
主站蜘蛛池模板: 开封县| 新野县| 湟源县| 襄汾县| 龙岩市| 浏阳市| 台中市| 安乡县| 临颍县| 延寿县| 宽城| 中江县| 鹰潭市| 时尚| 洛阳市| 阿勒泰市| 大渡口区| 西丰县| 江达县| 图们市| 五指山市| 凉山| 启东市| 马关县| 辽宁省| 玛纳斯县| 徐汇区| 驻马店市| 盐边县| 墨脱县| 筠连县| 吉隆县| 镇康县| 喜德县| 永城市| 长乐市| 海原县| 蒲江县| 平泉县| 武胜县| 新巴尔虎右旗|