- 您現在的位置：買賣IC網 > PDF目錄192296 > S29GL032M10BFIR12 (SPANSION LLC) MirrorBit Flash Family PDF資料下載
參數資料
| 型號： | S29GL032M10BFIR12 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | MirrorBit Flash Family |
| 中文描述： | 2M X 16 FLASH 3V PROM, 100 ns, PBGA64 |
| 封裝： | 13 X 11 MM, LEAD FREE, FORTIFIED BGA-64 |
| 文件頁數： | 19/158頁 |
| 文件大小： | 4695K |
| 代理商： | S29GL032M10BFIR12 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
August 4, 2004 S29GLxxxM_00_B1_E
S29GLxxxM MirrorBitTM Flash Family
115
Da ta shee t
Write Operation Status
The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5, DQ6,
and DQ7. Table 19 and the following subsections describe the function of these bits. DQ7 and DQ6 each offer a
method for determining whether a program or erase operation is complete or in progress. The device also pro-
vides a hardware-based output signal, RY/BY#, to determine whether an Embedded Program or Erase operation
is in progress or has been completed.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in
progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising edge of
the final WE# pulse in the command sequence.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed
to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algo-
rithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program
address to read valid status information on DQ7. If a program address falls within a protected sector, Data# Polling
on DQ7 is active for approximately 1 s, then the device returns to the read mode.
During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7. When the Embedded Erase algo-
rithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7. The
system must provide an address within any of the sectors selected for erasure to read valid status information on
DQ7.
After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on
DQ7 is active for approximately 100 s, then the device returns to the read mode. If not all selected sectors are
protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that
are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be
valid.
Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with
DQ0–DQ6 while Output Enable (OE#) is asserted low. That is, the device may change from providing status in-
formation to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read the status
or valid data. Even if the device has completed the program or erase operation and DQ7 has valid data, the data
outputs on DQ0–DQ6 may be still invalid. Valid data on DQ0–DQ7 will appear on successive read cycles.
Table 37 shows the outputs for Data# Polling on DQ7. Figure 7 shows the Data# Polling algorithm. Figure 17 in
the AC Characteristics section shows the Data# Polling timing diagram.
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL032M10BFIR13 | MirrorBit Flash Family |
| S29GL032M10BFIR30 | T528 Series - I, M, Z Case Sizes - Face Down Termination Tantalum Surface Mount Capacitor; Capacitance [nom]: 220uF; Working Voltage (Vdc)[max]: 6.3V; Capacitance Tolerance: +/-20%; Dielectric: Tantalum, Solid; ESR: 12mΩ; Lead Style: Surface-Mount Chip; Lead Dimensions: 7343-17; Termination: 100% Tin (Sn); Body Dimensions: 7.3mm x 4.3mm x 1.7mm; Temperature Range: -55C to +105C; Container: Tape & Reel; Qty per Container: 1,000; Features: Face Down Termination |
| S29GL032M10FAIR22 | MirrorBit Flash Family |
| S29GL032M10FAIR23 | MirrorBit Flash Family |
| S29GL032M10FAIR30 | MirrorBit Flash Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL032M10BFIR13 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology |
| S29GL032M10BFIR20 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10BFIR22 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10BFIR23 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10BFIR30 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology |
發布緊急采購，3分鐘左右您將得到回復。