欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: S29GL032M10FAIR22
廠商: SPANSION LLC
元件分類: PROM
英文描述: MirrorBit Flash Family
中文描述: 2M X 16 FLASH 3V PROM, 100 ns, PBGA64
封裝: 13 X 11 MM, FORTIFIED, BGA-64
文件頁數: 88/116頁
文件大小: 6024K
代理商: S29GL032M10FAIR22
February 7, 2007 S29GL-M_00_B8
S29GL-M MirrorBitTM Flash Family
71
Data
Sheet
Write Operation Status
The device provides several bits to determine the status of a program or erase operation: DQ2,
DQ3, DQ5, DQ6, and DQ7. Table 36 and the following subsections describe the function of these
bits. DQ7 and DQ6 each offer a method for determining whether a program or erase operation is
complete or in progress. The device also provides a hardware-based output signal, RY/BY#, to
determine whether an Embedded Program or Erase operation is in progress or is completed.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase
algorithm is in progress or completed, or whether the device is in Erase Suspend. Data# Polling
is valid after the rising edge of the final WE# pulse in the command sequence.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the
datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend.
When the Embedded Program algorithm is complete, the device outputs the datum programmed
to DQ7. The system must provide the program address to read valid status information on DQ7.
If a program address falls within a protected sector, Data# Polling on DQ7 is active for approxi-
mately 1 s, then the device returns to the read mode.
During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7. When the Embed-
ded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling
produces a “1” on DQ7. The system must provide an address within any of the sectors selected
for erasure to read valid status information on DQ7.
After an erase command sequence is written, if all sectors selected for erasing are protected,
Data# Polling on DQ7 is active for approximately 100 s, then the device returns to the read
mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unpro-
tected sectors, and ignores the selected sectors that are protected. However, if the system reads
DQ7 at an address within a protected sector, the status may not be valid.
Just prior to the completion of an Embedded Program or Erase operation, DQ7 can change asyn-
chronously with DQ0–DQ6 while Output Enable (OE#) is asserted low. That is, the device can
change from providing status information to valid data on DQ7. Depending on when the system
samples the DQ7 output, it can read the status or valid data. Even if the device has completed
the program or erase operation and DQ7 has valid data, the data outputs on DQ0–DQ6 may be
still invalid. Valid data on DQ0–DQ7 appears on successive read cycles.
Table 36 shows the outputs for Data# Polling on DQ7. Figure 7 shows the Data# Polling algo-
rithm. Figure 17 shows the Data# Polling timing diagram.
相關PDF資料
PDF描述
S29GL032M10FAIR23 MirrorBit Flash Family
S29GL032M10FAIR30 MirrorBit Flash Family
S29GL032M10FAIR32 Tantalum Capacitor; Capacitance:220uF; Capacitance Tolerance:+/- 20 %; Working Voltage, DC:10V; Package/Case:7343-31; Terminal Type:PCB SMT; ESR:0.001ohm; Packaging:Cut Tape; Series:T530
S29GL032M10FAIR33 MirrorBit Flash Family
S29GL032M10FAIR40 MirrorBit Flash Family
相關代理商/技術參數
參數描述
S29GL032M10FAIR23 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology
S29GL032M10FAIR30 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10FAIR32 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10FAIR33 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology
S29GL032M10FAIR40 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology
主站蜘蛛池模板: 盱眙县| 长阳| 绍兴市| 陆川县| 名山县| 慈利县| 内乡县| 乌兰浩特市| 乌恰县| 靖西县| 政和县| 崇信县| 荣成市| 深州市| 常宁市| 绥德县| 长乐市| 修文县| 巴马| 漳州市| 雅江县| 莎车县| 志丹县| 介休市| 奉贤区| 娄底市| 上蔡县| 阆中市| 九龙坡区| 宜君县| 绿春县| 桐梓县| 明光市| 大田县| 甘德县| 广州市| 宕昌县| 南乐县| 乌鲁木齐市| 盐亭县| 长兴县|