- 您現在的位置：買賣IC網 > Datasheet目錄57 > SI4713-B30-GMR (Silicon Laboratories Inc)IC TX FM RADIO RPS/RDS 20UQFN Datasheet資料下載
參數資料
| 型號： | SI4713-B30-GMR |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 21/42頁 |
| 文件大小： | 430K |
| 描述： | IC TX FM RADIO RPS/RDS 20UQFN |
| 標準包裝： | 2,500 |
| 頻率： | 76MHz ~ 108MHz |
| 應用： | 通用 |
| 調制或協議： | FM |
| 電流 - 傳輸： | 18.8mA |
| 數據接口： | PCB，表面貼裝 |
| 天線連接器： | PCB，表面貼裝 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 封裝/外殼： | 20-UFQFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Si4712/13-B30
Rev. 1.1
21
including 32, 40, 44.1, and 48 kHz. The digital audio
interface enables low-power operation by eliminating
the need for redundant DACs and ADCs on the audio
baseband processor.
The Si4712/13 includes a low-noise stereo line input
(LIN/RIN) with programmable attenuation. To ensure
optimal audio performance, the Si4712/13 has a
transmit line input property that allows the user to
specify the peak amplitude of the analog input required
to reach maximum deviation level. The deviation levels
of the audio, pilot, and RDS/RBDS signals can be
independently programmed to customize FM transmitter
designs. The Si4712/13 has a programmable low audio
level and high audio level indicators that allows the user
to selectively enable and disable the carrier based on
the presence of audio content. In addition, the device
provides an overmodulation indicator to allow the user
to dynamically set the maximum deviation level. The
Si4712/13 has a programmable audio dynamic range
control that can be used to reduce the dynamic range of
the audio input signal and increase the volume at the
receiver. These features can dramatically improve the
end users listening experience.
The Si4712/13 is reset by applying a logic low on the
RST pin. This causes all register values to be reset to
their default values. The digital input/output interface
supply (V
IO
) provides voltage to the RST, SEN, SDIO,
RCLK, DIN, DFS, and DCLK pins and can be connected
to the audio baseband processor's supply voltage to
save power and remove the need for voltage level
translators. RCLK is not required for register operation.
The Si4712/13 reference clock is programmable,
supporting many RCLK inputs as shown in Table 9.
The S4712/13 are part of a family of broadcast audio
solutions offered in standard, 3 x 3 mm 20-pin QFN
packages. All solutions are layout compatible, allowing
a single PCB to accommodate various feature offerings.
The Si4712/13 includes line inputs to the on-chip
analog-to-digital converters (ADC), a programmable
reference clock input, and a configurable digital audio
interface. The chip supports I
2
C-compliant 2-wire, 8-bit
SPI, and a 3-wire control interface.
5.2. FM Transmitter
The transmitter (TX) integrates a stereo audio ADC to
convert analog audio signals to high fidelity digital
signals. Alternatively, digital audio signals can be
applied to the Si4712/13 directly to reduce power
consumption by eliminating the need to convert audio
baseband signals to analog and back again to digital.
Digital signal processing is used to perform the stereo
MPX encoding and FM modulation to a low digital IF.
Transmit baseband filters suppress out-of-channel
noise and images from the digital low-IF signal. A
quadrature single-sideband mixer up-converts the
digital IF signal to RF, and internal RF filters suppress
noise and harmonics to support the harmonic emission
requirements of cellular phones, GPS, WLAN, and other
wireless standards.
The TXO output has over 10 dB of output level control,
programmable in approximately 1 dB steps. This large
output range enables a variety of antennas to be used
for transmit, such as a monopole stub antenna or a loop
antenna. The 1 dB step size provides fine adjustment of
the output voltage.
The TXO output requires only one external 120 nH
inductor. The inductor is used to resonate the antenna
and is automatically calibrated within the integrated
circuit to provide the optimum output level and
frequency response for supported transmit frequencies.
Users are responsible for adjusting their systems
radiated power levels to comply with local regulations
on RF transmission (FCC, ETSI, ARIB, etc.).
5.3. Receive Power Scan
The Si4712/13 is the industrys first FM transmitter with
integrated receive functionality to measure received
signal strength. This has been designed to specifically
handle various antenna lengths including integrated
PCB antennas, wire antennas, and loop antennas,
allowing it to share the same antenna as the transmitter.
The receive function reuses the on-chip varactor from
the transmitter to optimize the receive signal power
applied to the front-end amplifier. Auto-calibration of the
varactor occurs with each tune command for consistent
performance across the FM band.
相關PDF資料 |
PDF描述 |
|---|---|
| SKY12146-321LF | IC VAR VOLT ATTEN 12QFN |
| SN171GG-NR | SNAP PROTOBOARD W/NO RADIO |
| SWLP.2450.12.4.B.02 | ANTENNA WI-FI WLAN 2.4GHZ |
| TD4A | SENSOR RTD LIQUID TEMP 2TERM |
| TD5A | SENSOR RTD TEMP MINI 3LEAD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI4713-B-EVB | 功能描述:射頻開發工具 SI4713 EVAL BOARD REV B RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| SI4714DY | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:N-Channel 30 V (D-S) MOSFET with Schottky Diode |
| Si4714DY-T1-GE3 | 功能描述:MOSFET 30 Volts 13.6 Amps 4.5 Watts RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| SI4719CY | 功能描述:電源開關 IC - 配電 P-Ch Battery Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| SI4719CY-E3 | 功能描述:電源開關 IC - 配電 P-Ch Battery Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。