- 您現在的位置：買賣IC網 > PDF目錄384921 > SMFLHP (Standard Power) DC/DC CONVERTERS 28 VOLT INPUT PDF資料下載
參數資料
| 型號： | SMFLHP |
| 廠商： | Standard Power |
| 英文描述： | DC/DC CONVERTERS 28 VOLT INPUT |
| 中文描述： | DC / DC轉換28伏的輸入 |
| 文件頁數： | 1/6頁 |
| 文件大小： | 264K |
| 代理商： | SMFLHP |
MODELS
VDC O
UTPUT
SINGLE
3.3
5
12
15
DUAL
±5
±12
±15
DESCRIPTION
The SMFLHP Series 28 volt DC/DC converters are rated up to
100 watts output power over a –55° to +125°C temperature range
with a 28 Vdc nominal input. On dual output models, up to 70% of
the rated output power can be drawn from either the positive or
negative outputs. Current sharing allows the units to be paralleled
for total power of up to 270 watts. The welded, hermetically sealed
package is only 3.005 x 1.505 x 0.400 inches, giving the series an
overall power density of up to 67 watts per cubic inch.
S
CREENING
SMFLHP converters offer screening options to Space Prototype (O),
Class H, or Class K. Available radiation hardness (RHA) levels are
O or R. See “QA Screening: Class H and K, QML” for more infor-
mation.
D
ESIGN
F
EATURES
The SMFLHP Series converters are switching regulators that use a
quasi-square wave, single ended forward converter design with a
constant switching frequency of 600 kHz.
Isolation between input and output circuits is provided with a trans-
former in the forward path and wide bandwidth magnetic coupling in
the feedback control loop. The SMFLHP Series uses a unique dual
loop feedback technique that controls output current with an inner
feedback loop and output voltage with a cascaded voltage mode
feedback loop.
The additional secondary current mode feedback loop improves
transient response in a manner similar to primary current mode
control and allows for ease of paralleling.
Tight load regulation is achieved through a wide-bandwidth
magnetic feedback circuit. The output voltage on single SMFLHP
models can be easily trimmed by adding an external resistor. (See
Figure 1 for voltage changes with different resistor values.)
I
NHIBIT
The SMFLHP Series converters have two TTL compatible inhibit
terminals (INH1 and INH2) that can be used to disable power
conversion, resulting in a very low quiescent input current. An open
collector TTL compatible low (<0.8 volts) is required between INH1
(pin 4) and Input Common (pin 2) to inhibit the converter. An open
collector TTL compatible low (<0.5 volts) is required between INH2
(pin 12) and Output Common (pin 8) to inhibit the converter. The
application of intermediate voltages to these pins (1.5 to 10.5 volts)
should be avoided.
C
URRENT
S
HARING AND
P
ARALLEL
O
PERATION
Multiple SMFLHP converters may be used in parallel to drive a
common load (see Figure 2). In this mode of operation the load
current is shared by two or three SMFLHP converters. In current
sharing mode, one SMFLHP converter is designated as a master.
The SLAVE pin (pin 11) of the master is left unconnected and the
MSTR/INH2 pin (pin 12) of the master is connected to the SLAVE
pin (pin 11) of the slave units. The units designated as slaves have
the MSTR/INH2 pin (pin 12) connected to the SNS RTN pin (pin 9).
Figure 2 shows the typical setup for two or three units in parallel.
Note that synchronizing the units together (though shown in the
figure) is not required for current sharing operation. A second slave
unit may be placed in parallel with a master and slave; this requires
the TRI pin (pin 3) of the master unit to be connected to the SNS
RTN pin (pin 9).
When paralleled, 90% of the total combined power ratings of the
SMFLHP converters are available at the load. Overload and short
circuit performance are not adversely affected during parallel
operation.
DC/DC C
ONVERTERS
28 V
OLT
I
NPUT
SMFLHPSERIES
100 WATT
F
EATURES
Fully qualified to Class H or K
–55° to +125°C operation
19 to 40 VDC input
Fully Isolated
Magnetic feedback
Fixed frequency, 600 kHz typical
Topology – Single Ended Forward
Inhibit function – input and output
Sync function
Output trim on single output models
Indefinite short circuit protection
Remote sense on single output models
Up to 87% efficiency
Parallelable up to 270 watts
Size (max.): 3.005 x 1.505 x 0.400 inches (76.33 x 38.23 x 10.16 mm)
See cases “U maximum dimensions” and “U” for dimensions.
Weight:
86 grams maximum
Screening:
Space Prototype, Class H, or Class K
Radiation hardness levels O or R
See “QA Screening: Class H and K, QML” for more information.
Available configurations: OO, HO, HR, KR
Interpoint, a Crane Co. Company
PO Box 97005 Redmond WA 98073-9705
425-895-4053 electronics@craneae.com
www.craneae.com/power
Contact Information
相關PDF資料 |
PDF描述 |
|---|---|
| SMFL | Single and Dual DC/DC Converters |
| SMH4802 | Programmable -48V Hot-Swap Controller with Forced Shut Down |
| SMH4803A | Distributed Power Hot Swap Controller |
| SMH4803AS | Distributed Power Hot Swap Controller |
| SMH4804 | -48V Programmable Hot Swap Sequencing Power Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SMFLHP2805D | 制造商:INTERPOINT 制造商全稱:INTERPOINT 功能描述:Parallel operation with current share, up to 3 units (228 watts) |
| SMFLHP2805D/KR | 制造商:INTERPOINT 制造商全稱:INTERPOINT 功能描述:DC/DC CONVERTERS 28 VOLT INPUT |
| SMFLHP2805D_07 | 制造商:INTERPOINT 制造商全稱:INTERPOINT 功能描述:Parallel operation with current share, up to 3 units (228 watts) |
| SMFLHP2805S | 制造商:INTERPOINT 制造商全稱:INTERPOINT 功能描述:Parallel operation with current share, up to 3 units (228 watts) |
| SMFLHP2805S/KR | 制造商:INTERPOINT 制造商全稱:INTERPOINT 功能描述:DC/DC CONVERTERS 28 VOLT INPUT |
發布緊急采購，3分鐘左右您將得到回復。