- 您現在的位置：買賣IC網 > PDF目錄98217 > THS10064IDAR (TEXAS INSTRUMENTS INC) 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 PDF資料下載
參數資料
| 型號： | THS10064IDAR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| 封裝： | GREEN, PLASTIC, TSSOP-32 |
| 文件頁數： | 29/42頁 |
| 文件大小： | 527K |
| 代理商： | THS10064IDAR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
THS10064
SLAS255B – DECEMBER 1999 – REVISED DECEMBER 2002
www.ti.com
35
DC COUPLING
An operational amplifier can be configured to shift the signal level according to the analog input voltage range of the
THS10064. The analog input voltage range of the THS10064 goes from 1.5 V to 3.5 V. An op-amp specified for 5-V
single supply can be used as shown in Figure 44.
Figure 44 shows an application example where the analog input signal in the range from –1 V up to 1 V is shifted
by an op-amp to the analog input range of the THS10064 (1.5 V to 3.5 V). The op-amp is configured as an inverting
amplifier with a gain of –1. The required dc voltage of 1.25 V at the noninverting input is derived from the 2.5-V output
reference REFOUT of the THS10064 by using a resistor divider. Therefore, the op-amp output voltage is centered
at 2.5 V. The use of ratio matched, thin-film resistor networks minimizes gain and offset errors.
_
+
5 V
R
RS
3.5 V
2.5 V
1.5 V
THS10064
AINP
REFOUT
R
1.25 V
1 V
0 V
–1 V
REFIN
Figure 44. Level-Shift for DC-Coupled Input
DIFFERENTIAL MODE OF OPERATION
For the differential mode of operation, a conversion from single-ended to differential is required. A conversion to
differential signals can be achieved by using an RF-transformer, which provides a center tap. Best performance is
achieved in differential mode.
THS10064
AINP
AINM
REFOUT
C
R
200
49.9
Mini Circuits
T4–1
Figure 45. Transformer Coupled Input
相關PDF資料 |
PDF描述 |
|---|---|
| THS10064IDAG4 | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS1007CDA | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS1007CDAR | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS1007CDAG4 | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS1007IDA | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS1007 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT, 4 ANALOG INPUT, 6-MSPS, SIMULATANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
| THS1007CDA | 功能描述:模數轉換器 - ADC 10-Bit 6MSPS Simult Sampling Quad Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1007CDAG4 | 功能描述:模數轉換器 - ADC 10-Bit 6MSPS Simult Sampling Quad Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1007CDAR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT, 4 ANALOG INPUT, 6-MSPS, SIMULATANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
| THS1007IDA | 功能描述:模數轉換器 - ADC 10 BIT QUAD ADC w/o RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。