- 您現在的位置：買賣IC網 > PDF目錄98246 > TLE5250 (INFINEON TECHNOLOGIES AG) STEPPER MOTOR CONTROLLER, 3 A, PZFM15 PDF資料下載
參數資料
| 型號： | TLE5250 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 3 A, PZFM15 |
| 封裝： | PLASTIC, SIP-15 |
| 文件頁數： | 20/22頁 |
| 文件大小： | 142K |
| 代理商： | TLE5250 |
TLE 5250
Semiconductor Group
7
1998-02-01
Diagnostics
The information from the different parts of the circuit is collected in the diagnostics and
stored in the fault logic. The information is read out on the Diagnostics output (open
collector).
The fault logic consists of a 16-bit multiplexer that switches information in three
categories through to the Diagnostics output.
Bit 0 always appears inverted on DIAG when EN is High. This means that, if there is
overcurrent on the upper transistor, undervoltage or overtemperature, it will be signaled
immediately on the Diagnostics output. DIAG changes from High to Low.
Bit 1: check bit.
Bits 2, 3, 4 and 5 indicate the momentary status of the comparators on the two outputs
(see Figure 2). Changes in the status of the comparators for output monitoring can be
observed on DIAG when EN is Low and the counter of the multiplexer is on 2, 3, 4 or 5.
This is necessary for detecting underload.
Bits 6, 7, 8, 9
The monoflop generates a short strobe signal when the EN edge changes from High to
Low. The status of the comparators for output monitoring is stored with this signal and
can be read out in bits 6, 7, 8 and 9.
When Enable is Low, the Phase input is used as a clock input. As the edge rises, an
internal counter is incremented and the corresponding channel of the multiplexer is
switched through. As the edge falls, the signal is output inverted. When Enable is High,
the counter is reset to zero.
Figure 3
AED01467
EN
Strobe
Reset
相關PDF資料 |
PDF描述 |
|---|---|
| TLE6208-3G | BRUSH DC MOTOR CONTROLLER, 1.2 A, PDSO14 |
| TLE6208-6G | BRUSH DC MOTOR CONTROLLER, 2 A, PDSO28 |
| TLE6210G | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO20 |
| TLE6266G | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| TLE6280GP | BRUSHLESS DC MOTOR CONTROLLER, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLE6208-3G | 功能描述:馬達/運動/點火控制器和驅動器 Triple-Half-Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TLE6208-3-G | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Triple-Half-Bridge |
| TLE6208-3G_07 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Triple Half Bridges Optimized for DC motor management applications |
| TLE62083GXUMA1 | 制造商:Infineon Technologies AG 功能描述:Triple Half Bridge Motor Driver 14-Pin DSO 制造商:Infineon Technologies AG 功能描述:BODY BRIDGES - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC MOTOR DRIVER SPI 14DSO |
| TLE6208-6 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Hex-Half-Bridge / Double Six-Driver |
發布緊急采購，3分鐘左右您將得到回復。