- 您現在的位置：買賣IC網 > PDF目錄98252 > TLV320AIC10CGQER (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PBGA80 PDF資料下載
參數資料
| 型號： | TLV320AIC10CGQER |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
| 封裝： | MICRO, PLASTIC, BGA-80 |
| 文件頁數： | 22/57頁 |
| 文件大小： | 454K |
| 代理商： | TLV320AIC10CGQER |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
3–3
3.2.1
Register Programming
All register programming occurs during secondary communication through DIN or ALTI, and data are latched and
valid on the falling edge of the SCLK during the frame-sync signal. If the default value of a particular register is desired,
that register does not need to be addressed during the secondary communication interval. The NOOP command
(DS15-DS8 all set to 0) addresses the pseudo-register (register 0), and no register programming takes place during
the communication.
In addition, each register can be read back through DOUT during secondary communications by setting the read bit
(D12) to 1. When a register is in the read mode, no data can be written to the register during this cycle. A subsequent
secondary communication is required to return this register to the write mode.
For example, if the contents of control register 1 of device 3 are desired to be read out from DOUT, the following
procedure must be performed through DIN:
Request secondary communication by setting either D0 = 1(software request), or FC = high (hardware
request) during the primary communication interval.
During the secondary communication interval (FS), send data in through DIN using the following format:
Device Address
RW
Register Address
X
Register Content
0
1
0
1
x
DS15
DS0
Then, during the same frame, the following data is read from DOUT; the last 8 bits of DOUT contains
register 1 data.
Device Address
RW
Register Address
X
Register Content
0
1
x
d
DS15
DS0
Figure 3–3 is the timing diagram of this procedure.
DOUT
PS
DIN
Register 1 Read
FS
Low 8 Bit (D0 – D7) Is
the Content of Register
1
Figure 3–3. Device 3/Register 1 Read Operation Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| TLV320AIC10IGQER | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
| TLV320AIC11C | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TLV320AIC11I | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TLV320AIC11CPFB | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TLV320AIC11IPFB | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLV320AIC10CPFB | 功能描述:接口—CODEC 16-Bit 22-KSPS DSP Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLV320AIC10CPFBG4 | 功能描述:接口—CODEC 16-Bit Reg Trnscvr With 3-State Outputs RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLV320AIC10EVM | 功能描述:音頻 IC 開發工具 TLV320AIC10 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TLV320AIC10I | 制造商:TI 制造商全稱:Texas Instruments 功能描述:General-Purpose 3V to 5.5V 16-bit 22-KSPS DSP CODEC |
| TLV320AIC10IGQER | 功能描述:接口—CODEC 16-Bit 22-KSPS DSP Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。