- 您現在的位置：買賣IC網 > PDF目錄384999 > TMC249-SA (Electronic Theatre Controls, Inc.) High Current Microstep Stepper Motor Driver with sensorless stall detection, protection / diagnostics and SPI Interface PDF資料下載
參數資料
| 型號： | TMC249-SA |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | High Current Microstep Stepper Motor Driver with sensorless stall detection, protection / diagnostics and SPI Interface |
| 中文描述： | 大電流微步步進電機驅動器，帶有傳感器的失速檢測，保護/診斷和SPI接口 |
| 文件頁數： | 1/25頁 |
| 文件大小： | 219K |
| 代理商： | TMC249-SA |
TMC249 / TMC249A DATA SHEET (V2.02 / Aug 12th, 2005)
1
Copyright 2005, TRINAMIC Motion Control GmbH & Co KG
TMC 249/A – DATA SHEET
High Current Microstep Stepper Motor Driver
with sensorless stall detection, protection /
diagnostics and SPI Interface
TRINAMIC
Motion Control GmbH & Co KG
Sternstrae 67
D – 20357 Hamburg
GERMANY
T +49 - (0) 40 - 51 48 06 - 0
F +49 - (0) 40 - 51 48 06 - 60
WWW.TRINAMIC.COM
INFO@TRINAMIC.COM
Features
The TMC249 / TMC249A (1) is a dual full bridge driver IC for bipolar stepper motor control
applications. The TMC249 is realized in a HVCMOS technology and directly drives eight external Low-
RDS-ON high efficiency MOSFETs. It supports more than 4000mA coil current. The low power
dissipation makes the TMC249 an optimum choice for drives, where a high reliability is desired. With
additional drivers, motor current and voltage can be increased. The integrated unique sensorless stall
detection (pat. pend.) StallGuard makes it a good choice for applications, where a reference point is
needed, but where a switch is not desired. Its ability to predict an overload makes the TMC249 an
optimum choice for drives, where a high reliability is desired. Internal DACs allow microstepping as
well as smart current control. The device can be controlled by a serial interface (SPI
i
) or by analog /
digital input signals. Short circuit, temperature, undervoltage and overvoltage protection are
integrated.
More than 4000mA using 8 external MOS transistors (e.g. 2.8A RMS)
Sensorless stall detection StallGuard and load measurement integrated
Control via SPI with easy-to-use 12 bit protocol or external analog / digital signals
Short circuit, overvoltage and overtemperature protection integrated
Status flags for overcurrent, open load, over temperature, temperature pre-warning, undervoltage
Integrated 4 bit DACs allow up to 16 times microstepping via SPI, any resolution via analog
control
Mixed decay feature for smooth motor operation
Slope control user programmable to reduce electromagnetic emissions
Chopper frequency programmable via a single capacitor or external clock
Current control allows cool motor and driver operation
7V to 34V motor supply voltage (A-type)
External drivers can be added for higher motor voltages and higher currents (e.g. 50V, 5A)
3.3V or 5V operation for digital part
Low power dissipation via low RDS-ON power stage
Standby and shutdown mode available
Choice of SO28 or chip size MLF package
(1) The term TMC249 in this datasheet always refers to the TMC249A and the TMC249. The major
differences in the older TMC249 are explicitly marked with “non-A-type”. The TMC249A brings a
number of enhancements and is fully backward compatible to the TMC249.
相關PDF資料 |
PDF描述 |
|---|---|
| TMC2601 | 140-370 MHz Output Frequency Digital Video Serial Transmission Encoder （8- or 10-bit Parallel Data Into Serial Format）(140-370 MHz 輸出頻率的數字視頻串行傳輸譯碼器（8位或10位并行數據轉換成串行格式）) |
| TMC3211 | 32-Bit, 20 MOPS Integer Divider(32位,20MOPS 整數除法器) |
| TMC428 | Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces |
| TMD0305-2 | Microwave Power GaAs MMIC(微波功率砷化鎵MMIC) |
| TMD1414-2C | MICROWAVE POWER MMIC AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|
發布緊急采購，3分鐘左右您將得到回復。