欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TMJ320C6211GLZ167
廠商: Texas Instruments, Inc.
元件分類: 數字信號處理
英文描述: FIXED-POINT DIGITAL SIGNAL PROCESSORS
中文描述: 定點數字信號處理器
文件頁數: 38/83頁
文件大小: 1176K
代理商: TMJ320C6211GLZ167
TMS320C6211, TMS320C6211B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS073K
AUGUST 1998
REVISED MARCH 2004
38
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251
1443
IEEE 1149.1 JTAG compatibility statement
The TMS320C6211/C6211B DSP requires that both TRST and RESET resets be asserted upon power up to
be properly initialized. While RESET initializes the DSP core, TRST initializes the DSP’s emulation logic. Both
resets are required for proper operation.
While both TRST and RESET need to be asserted upon power up, only RESET needs to be released for the
DSP to boot properly. TRST may be asserted indefinitely for normal operation, keeping the JTAG port interface
and DSP’s emulation logic in the reset state.
TRST only needs to be released when it is necessary to use a JTAG controller to debug the DSP or exercise
the DSP’s boundary scan functionality.
For maximum reliability, the TMS320C6211/C6211B DSP includes an internal pulldown (IPD) on the TRST pin
to ensure that TRST will always be asserted upon power up and the DSP’s internal emulation logic will always
be properly initialized.
JTAG controllers from Texas Instruments actively drive TRST high. However, some third-party JTAG controllers
may not drive TRST high but expect the use of an external pullup resistor on TRST.
When using this type of JTAG controller, assert TRST to initialize the DSP after powerup and externally drive
TRST high before attempting any emulation or boundary scan operations. Following the release of RESET, the
low-to-high transition of TRST must be “seen” to latch the state of EMU1 and EMU0. The EMU[1:0] pins
configure the device for either Boundary Scan mode or Emulation mode. For more detailed information, see
the terminal functions section of this data sheet.
EMIF device speed
TI recommends utilizing the input/output buffer information specification (IBIS) models to analyze all AC timings.
To properly use IBIS models to attain accurate timing analysis for a given system, see the
Using IBIS Models
for Timing Analysis
application report (literature number SPRA839).
相關PDF資料
PDF描述
TMX320C6202PYP167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMX320C6202BPYP167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMX320C6203BPYP167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMX320C6211BPYP167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMP320C6202BPYP167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
相關代理商/技術參數
參數描述
TMJ320C6211GNY167 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMJ320C6211GNZ167 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMJ320C6211PYP167 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMJ325AB7475KMHP 功能描述:CAP CER 4.7UF 25V X7R 1210 制造商:taiyo yuden 系列:M 包裝:剪切帶(CT) 零件狀態:在售 電容:4.7μF 容差:±10% 電壓 - 額定:25V 溫度系數:X7R 工作溫度:-55°C ~ 125°C 特性:軟端子 等級:AEC-Q200 應用:汽車,SMPS 濾波,Boardflex 敏感 故障率:- 安裝類型:表面貼裝,MLCC 封裝/外殼:1210(3225 公制) 大小/尺寸:0.126" 長 x 0.098" 寬(3.20mm x 2.50mm) 高度 - 安裝(最大值):- 厚度(最大值):0.110"(2.80mm) 引線間距:- 引線形式:- 標準包裝:1
TMJ325AB7475KMHT 功能描述:4.7μF 25V 陶瓷電容器 X7R 1210(3225 公制) 0.126" 長 x 0.098" 寬(3.20mm x 2.50mm) 制造商:taiyo yuden 系列:M 包裝:剪切帶(CT) 零件狀態:有效 電容:4.7μF 容差:±10% 電壓 - 額定:25V 溫度系數:X7R 安裝類型:表面貼裝,MLCC 工作溫度:-55°C ~ 125°C 應用:汽車級,Boardflex 敏感 等級:AEC-Q200 封裝/外殼:1210(3225 公制) 大小/尺寸:0.126" 長 x 0.098" 寬(3.20mm x 2.50mm) 高度 - 安裝(最大值):- 厚度(最大值):0.106"(2.70mm) 引線間距:- 特性:軟端子 引線形式:- 標準包裝:1
主站蜘蛛池模板: 舞钢市| 抚顺县| 清原| 长宁县| 教育| 遵化市| 墨竹工卡县| 土默特左旗| 云阳县| 城固县| 楚雄市| 环江| 平南县| 永新县| 运城市| 滦南县| 汝州市| 萨迦县| 兰坪| 永福县| 呼图壁县| 前郭尔| 新河县| 大庆市| 宝鸡市| 岗巴县| 庆城县| 盘山县| 乌苏市| 霍邱县| 桐庐县| 盖州市| 嵊州市| 滦南县| 清远市| 漳平市| 新巴尔虎左旗| 乌兰县| 沧州市| 台东市| 平乐县|