- 您現在的位置：買賣IC網 > PDF目錄382673 > TPA032D02DCAR Dual Audio Amplifier PDF資料下載
參數資料
| 型號： | TPA032D02DCAR |
| 元件分類： | 運動控制電子 |
| 英文描述： | Dual Audio Amplifier |
| 中文描述： | 雙音頻放大器 |
| 文件頁數： | 24/31頁 |
| 文件大?。?/td> | 445K |
| 代理商： | TPA032D02DCAR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
TPA0312
2-W STEREO AUDIO POWER AMPLIFIER
WITH FOUR SELECTABLE GAIN SETTINGS AND MUX CONTROL
SLOS335 –DECEMBER 2000
24
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4
×
the output power of the SE
configuration. Internal dissipation versus output power is discussed further in the crest factor and thermal
considerationssection.
single-ended operation
In SE mode the load is driven from the primary amplifier output for each channel (OUT+, terminals 21 and 4).
The amplifier switches single-ended operation when the SE/BTL terminal is held high. This puts the negative
outputs in a high-impedance state, and reduces the amplifier’s gain to 1 V/V.
input MUX operation
The input MUX allows two separate inputs to be applied to the amplifier. This allows the designer to choose
which input is active independent of the state of the SE/BTL terminal. When the HP/LINE terminal is held high,
the headphone inputs are active. When the HP/LINE terminal is held low, the line BTL inputs are active.
BTL amplifier efficiency
Class-AB amplifiers are notoriously inefficient. The primary cause of these inefficiencies is voltage drop across
the output stage transistors. There are two components of the internal voltage drop. One is the headroom or
dc voltage drop that varies inversely to output power. The second component is due to the sinewave nature of
the output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from
V
DD
. The internal voltage drop multiplied by the RMS value of the supply current, I
DD
rms, determines the internal
power dissipation of the amplifier.
An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power
supply to the power delivered to the load. To accurately calculate the RMS and average values of power in the
load and in the amplifier, the current and voltage waveform shapes must first be understood (see Figure 41).
V(LRMS)
VO
IDD
IDD(avg)
Figure 41. Voltage and Current Waveforms for BTL Amplifiers
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are very
different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified
shape, whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different.
Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
The following equations are the basis for calculating amplifier efficiency.
相關PDF資料 |
PDF描述 |
|---|---|
| TPA100RL | SINGLE BIDIRECTIONAL BREAKOVER DIODE|133V V(BO) MAX|800MA I(S)|DO-204AC |
| TPA120RL | DIP Switch; No. of Switch Positions:6; Circuitry:SPST; Contact Current Max:25mA; Switch Terminals:SMT Gull Wing; Overall Length:8.75mm; Pitch Spacing:1.28mm; Series:TDA; Actuator Style:Flush Slide RoHS Compliant: Yes |
| TPA130RL | SINGLE BIDIRECTIONAL BREAKOVER DIODE|173V V(BO) MAX|800MA I(S)|DO-204AC |
| TPA180RL | SINGLE BIDIRECTIONAL BREAKOVER DIODE|240V V(BO) MAX|800MA I(S)|DO-204AC |
| TPA200RL | Pushbutton Switch; Actuator Diameter:0.1"; Circuitry:SPST; Switch Operation:(On)-Off; Contact Rating:0.4VA at 20VAC/VDC; Features:Plunger Actuator; Leaded Process Compatible:Yes; Mounting Type:PCB; Peak Reflow Compatible (260 C):Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA032D02DCARG4 | 功能描述:音頻放大器 Stereo Medium Power Class-D Audio Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA032D02EVM | 制造商:Texas Instruments 功能描述:CLASS-D STEREO AUDIO POWER AMP EVM - Bulk |
| TPA032D03 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-W MONO CLASS-D AUDIO POWER AMPLIFIER |
| TPA032D03_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-W MONO CLASS-D AUDIO POWER AMPLIFIER |
| TPA032D03DCA | 功能描述:音頻放大器 10W Monaur RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。