欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TPA2014D1RGPRG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 音頻/視頻放大
英文描述: 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC20
封裝: 4 X 4 MM, GREEN, PLASTIC, QFN-20
文件頁數: 11/27頁
文件大小: 945K
代理商: TPA2014D1RGPRG4
Copper TraceWidth
Solder PadWidth
SolderMask Opening
Copper Trace Thickness
SolderMask Thickness
Trace Width
www.ti.com ............................................................................................................................................................... SLAS559A – MAY 2008 – REVISED JUNE 2008
Figure 18. Land Pattern Dimensions
Table 5. Land Pattern Dimensions
SOLDER PAD
SOLDER MASK
COPPER
STENCIL
COPPER PAD
DEFINITIONS
OPENING
THICKNESS
OPENING
THICKNESS
Nonsolder mask
275
m
375
m
275
m x 275 m Sq.
1 oz max (32
m)
125
m thick
defined (NSMD)
(+0.0, –25
m)
(+0.0, –25
m)
(rounded corners)
NOTES:
1. Circuit traces from NSMD defined PWB lands should be 75
m to 100 m wide in the exposed area inside
the solder mask opening. Wider trace widths reduce device stand off and impact reliability.
2. Recommend solder paste is Type 3 or Type 4.
3. Best reliability results are achieved when the PWB laminate glass transition temperature is above the
operating the range of the intended application.
4. For a PWB using a Ni/Au surface finish, the gold thickness should be less 0.5 mm to avoid a reduction in
thermal fatigue performance.
5. Solder mask thickness should be less than 20
m on top of the copper circuit pattern.
6. Best solder stencil performance is achieved using laser cut stencils with electro polishing. Use of chemically
etched stencils results in inferior solder paste volume control.
7. Trace routing away from WCSP device should be balanced in X and Y directions to avoid unintentional
component movement due to solder wetting forces.
Recommended trace width at the solder balls is 75
m to 100 m to prevent solder wicking onto wider PCB
traces.
For high current pins (SW, PGND, VOUT+, VOUT–, VCCIN, and VCCOUT) of the TPA2014D1, use 100 m trace
widths at the solder balls and at least 500
m PCB traces to ensure proper performance and output power for
the device.
For low current pins (IN–, IN+, SDd, SDb, GAIN, VCCFB, VDD) of the TPA2014D1, use 75 m to 100 m trace
widths at the solder balls. Run IN- and IN+ traces side-by-side to maximize common-mode noise cancellation.
Copyright 2008, Texas Instruments Incorporated
19
Product Folder Link(s): TPA2014D1
相關PDF資料
PDF描述
TPA2015D1YZHR 1.7 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA16
TPA2015D1YZHT 1.7 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA16
TPA2016D2YZHR 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA16
TPA2016D2YZHT 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA16
TPA2016D2RTJR 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20
相關代理商/技術參數
參數描述
TPA2014D1RGPT 功能描述:音頻放大器 1.5W Constant Out Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA2014D1RGPTG4 功能描述:音頻放大器 1.5W Constant Output Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA2014D1YZHR 功能描述:音頻放大器 1.5W Constant Output Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA2014D1YZHT 功能描述:音頻放大器 1.5W Constant Output Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA2015D1 制造商:TI 功能描述:2 W Constant Output Power Class-D Audio Amplifier With Adaptive Boost Converter and Battery Tracking SpeakerGuard? AGC
主站蜘蛛池模板: 天峻县| 宁都县| 石首市| 西畴县| 铅山县| 专栏| 平遥县| 乌鲁木齐市| 维西| 湄潭县| 慈利县| 鄂托克前旗| 托克逊县| 玉门市| 惠安县| 禄丰县| 奈曼旗| 英山县| 河曲县| 舒城县| 曲阜市| 新晃| 化德县| 辽源市| 建平县| 成武县| 武穴市| 璧山县| 永福县| 南部县| 中方县| 邹城市| 峡江县| 南昌县| 天气| 卓尼县| 龙门县| 台山市| 郯城县| 孝义市| 绵竹市|