- 您現在的位置：買賣IC網 > PDF目錄98271 > TPA2014D1RGPRG4 (TEXAS INSTRUMENTS INC) 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC20 PDF資料下載
參數資料
| 型號： | TPA2014D1RGPRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| 封裝： | 4 X 4 MM, GREEN, PLASTIC, QFN-20 |
| 文件頁數： | 9/27頁 |
| 文件大小： | 945K |
| 代理商： | TPA2014D1RGPRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
FILTER FREE OPERATION AND FERRITE BEAD FILTERS
1nF
Ferrite
ChipBead
OUTP
OUTN
1nF
Ferrite
ChipBead
OPERATION WITH DACs AND CODECs
BYPASSING THE BOOST CONVERTER
www.ti.com ............................................................................................................................................................... SLAS559A – MAY 2008 – REVISED JUNE 2008
A ferrite bead filter is often used if the design is failing radiated emissions without an LC filter and the frequency
sensitive circuit is greater than 1 MHz. This filter functions well for circuits that just have to pass FCC and CE
because FCC and CE only test radiated emissions greater than 30 MHz. When choosing a ferrite bead, choose
one with high impedance at high frequencies, and a low impedance at low frequencies. In addition, select a
ferrite bead with adequate current rating to prevent distortion of the output signal.
Use an LC output filter if there are low frequency (< 1 MHz) EMI sensitive circuits and/or there are long leads
from amplifier to speaker.
Figure 16 shows a typical ferrite bead output filters.
Figure 16. Typical Ferrite Chip Bead Filter
Suggested Chip Ferrite Bead
Load
Vendor
Part Number
Size
8
Murata
BLM18EG121SN1
0603
When using switching amplifiers with CODECs and DACs, there may be an increase in the output noise floor
from the audio amplifier. This occurs when mixing of the output frequencies of the CODEC/DAC with the
switching frequencies of the audio amplifier input stage. The noise increase is solved by placing a low-pass filter
between the CODEC/DAC and audio amplifier. This filters off the high frequencies that cause the problem and
allow proper performance.
The TPA2014D1 has a two pole low pass filter at the inputs. The cutoff frequency of the filter is set to
approximately 100kHz. The integrated low pass filter of the TPA2014D1 eliminates the need for additional
external filtering components. A properly designed additional low pass filter may be added without altering the
performance of the device.
Bypass the boost converter to drive the Class-D amplifier directly from the battery. Place a Shottky diode
between the SW pin and the VCCIN pin. Select a diode that has an average forward current rating of at least 1A,
reverse breakdown voltage of 10 V or greater, and a forward voltage as small as possible. See Figure 17 for an
example of a circuit designed to bypass the boost converter.
Do not configure the circuit to bypass the boost converter if VDD is higher than VCC when the boost converter is
enabled (SDb
≥ 1.3 V); VDD must be lower than VCC for proper operation. VDD may be set to any voltage within
the recommended operating range when the boost converter is disabled (SDb
≤ 0.3V).
Place a logic high on SDb to place the TPA2014D1 in boost mode. Place a logic low on SDb to place the
TPA2014D1 in bypass mode.
Copyright 2008, Texas Instruments Incorporated
17
Product Folder Link(s): TPA2014D1
相關PDF資料 |
PDF描述 |
|---|---|
| TPA2015D1YZHR | 1.7 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA16 |
| TPA2015D1YZHT | 1.7 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA16 |
| TPA2016D2YZHR | 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA16 |
| TPA2016D2YZHT | 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA16 |
| TPA2016D2RTJR | 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2014D1RGPT | 功能描述:音頻放大器 1.5W Constant Out Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2014D1RGPTG4 | 功能描述:音頻放大器 1.5W Constant Output Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2014D1YZHR | 功能描述:音頻放大器 1.5W Constant Output Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2014D1YZHT | 功能描述:音頻放大器 1.5W Constant Output Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2015D1 | 制造商:TI 功能描述:2 W Constant Output Power Class-D Audio Amplifier With Adaptive Boost Converter and Battery Tracking SpeakerGuard? AGC |
發布緊急采購，3分鐘左右您將得到回復。