- 您現在的位置：買賣IC網 > PDF目錄98271 > TPA2028D1YZFT (TEXAS INSTRUMENTS INC) 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 PDF資料下載
參數資料
| 型號： | TPA2028D1YZFT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| 封裝： | 1.63 X 1.63 MM, GREEN, DSBGA-9 |
| 文件頁數： | 24/37頁 |
| 文件大小： | 1812K |
| 代理商： | TPA2028D1YZFT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
SLOS660A
– JANUARY 2010 – REVISED MARCH 2011
Figure 44. Land Pattern Dimensions
Table 6. Land Pattern Dimensions(1) (2) (3) (4)
SOLDER PAD
SOLDER MASK(5)
COPPER
STENCIL
COPPER PAD
STENCIL(6) (7) OPENING
DEFINITIONS
OPENING
THICKNESS
275
μm
375
μm
Non solder mask
275
μm × 275 μm Sq. (rounded
1 oz max (32
μm)
125
μm thick
defined (NSMD)
corners)
(+0.0,
–25 μm)
(+0.0,
–25 μm)
(1)
Circuit traces from NSMD defined PWB lands should be 75
μm to 100 μm wide in the exposed area inside the solder mask opening.
Wider trace widths reduce device stand off and impact reliability.
(2)
Best reliability results are achieved when the PWB laminate glass transition temperature is above the operating the range of the
intended application.
(3)
Recommend solder paste is Type 3 or Type 4.
(4)
For a PWB using a Ni/Au surface finish, the gold thickness should be less 0.5 mm to avoid a reduction in thermal fatigue performance.
(5)
Solder mask thickness should be less than 20
μm on top of the copper circuit pattern
(6)
Best solder stencil performance is achieved using laser cut stencils with electro polishing. Use of chemically etched stencils results in
inferior solder paste volume control.
(7)
Trace routing away from WCSP device should be balanced in X and Y directions to avoid unintentional component movement due to
solder wetting forces.
COMPONENT LOCATION
Place all the external components very close to the TPA2028D1. Placing the decoupling capacitor, CS, close to
the TPA2028D1 is important for the efficiency of the Class-D amplifier. Any resistance or inductance in the trace
between the device and the capacitor can cause a loss in efficiency.
TRACE WIDTH
Recommended trace width at the solder balls is 75
μm to 100 μm to prevent solder wicking onto wider PCB
traces. For high current pins (PVDD (L, R), PGND, and audio output pins) of the TPA2028D1, use 100-
μm trace
widths at the solder balls and at least 500-
μm PCB traces to ensure proper performance and output power for
the device. For the remaining signals of the TPA2028D1, use 75-
μm to 100-μm trace widths at the solder balls.
The audio input pins (IN+ and IN
–) must run side-by-side to maximize common-mode noise cancellation
30
Copyright
2010–2011, Texas Instruments Incorporated
Product Folder Link(s): TPA2028D1
相關PDF資料 |
PDF描述 |
|---|---|
| TPA2031D1YZFT | 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA9 |
| TPA2031D1YZF | 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA9 |
| TPA2031D1YZFR | 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA9 |
| TPA2032D1YZFR | 2.75 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA9 |
| TPA2032D1YZF | 2.75 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA9 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2028D1YZFT | 制造商:Texas Instruments 功能描述:SPEAKER AMPLIFIER IC |
| TPA2029D1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-W Mono Class-D Audio Amplifier With SmartGain? AGC/DRC |
| TPA2029D1YZFEVM | 功能描述:音頻 IC 開發工具 TPA2029D1 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA2029D1YZFR | 功能描述:音頻放大器 3W Mono Class-D Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2029D1YZFT | 功能描述:音頻放大器 3W Mono Class-D Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。