- 您現在的位置：買賣IC網 > PDF目錄98276 > TPA6130A2YZHR (TEXAS INSTRUMENTS INC) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, BGA16 PDF資料下載
參數資料
| 型號： | TPA6130A2YZHR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, BGA16 |
| 封裝： | 2 X 2 MM, GREEN, DSBGA-16 |
| 文件頁數： | 6/28頁 |
| 文件大?。?/td> | 1198K |
| 代理商： | TPA6130A2YZHR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
www.ti.com
C(DCINPUT-BLOCKING)
1
2
CIN =
(3)
fc
IN +
1
2p R
IN CIN
C
IN +
1
2p fc
IN RIN
or
(4)
Charge Pump Flying Capacitor and CPVSS Capacitor
Decoupling Capacitors
Layout Recommendations
Exposed Pad On TPA6130A2RTJ Package Option
GND Connections
I
2C CONTROL INTERFACE DETAILS
Addressing the TPA6130A2
SLOS488B – NOVEMBER 2006 – REVISED FEBRUARY 2008
CIN is a theoretical capacitor used for mathematical calculations only. Its value is the series combination of the dc
input-blocking capacitors, C(DCINPUT-BLOCKING). Use Equation 3 to determine the value of C(DCINPUT-BLOCKING). For
example, if CIN is equal to 0.22 F, then C(DCINPUT-BLOCKING) is equal to about 0.47 F.
The two C(DCINPUT-BLOCKING) capacitors form a high-pass filter with the input impedance of the TPA6130A2. Use
Equation 3 to calculate CIN, then calculate the cutoff frequency using CIN and the differential input impedance of
the TPA6130A2, RIN, using Equation 4. Note that the differential input impedance changes with gain. See
Figure 33 for input impedance values. The frequency and/or capacitance can be determined when one of the two
values are given.
If a high pass filter with a -3 dB point of no more than 20 Hz is desired over all gain settings, the minimum
impedance would be used in the above equation. Figure 33 shows this to be 37 k
. The capacitor value by the
above equation would be 0.215
F. However, this is C
IN, and the desired value is for C(DCINPUT-BLOCKING).
Multiplying CIN by 2 yields 0.43 F, which is close to the standard capacitor value of 0.47 F. Place 0.47 F
capacitors at each input terminal of the TPA6130A2 to complete the filter.
The charge pump flying capacitor serves to transfer charge during the generation of the negative supply voltage.
The CPVSS capacitor must be at least equal to the flying capacitor in order to allow maximum charge transfer.
Low ESR capacitors are an ideal selection, and a value of 1 F is typical.
The TPA6130A2 is a DirectPath headphone amplifier that requires adequate power supply decoupling to
ensure that the noise and total harmonic distortion (THD) are low. Use good low equivalent-series-resistance
(ESR) ceramic capacitors, typically 1.0 F. Find the smallest package possible, and place as close as possible to
the device VDD lead. Placing the decoupling capacitors close to the TPA6130A2 is important for the performance
of the amplifier. Use a 10
F or greater capacitor near the TPA6130A2 to filter lower frequency noise signals.
The high PSRR of the TPA6130A2 will make the 10
F capacitor unnecessary in most applications.
Solder the exposed metal pad on the TPA6130A2RTJ QFN package to the a pad on the PCB. The pad on the
PCB may be grounded or may be allowed to float (not be connected to ground or power). If the pad is grounded,
it must be connected to the same ground as the GND pins (3, 9, 10, 13, and 19). See the layout and mechanical
drawings at the end of the datasheet for proper sizing. Soldering the thermal pad improves mechanical reliability,
improves grounding of the device, and enhances thermal conductivity of the package.
The GND pin for charge pump should be decoupled to the charge pump VDD pin, and the GND pin adjacent to
the Analog VDD pin should be separately decoupled to each other.
The device operates only as a slave device whose address is 1100000 binary.
14
Copyright 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA6130A2
相關PDF資料 |
PDF描述 |
|---|---|
| TPA6130A2YZHT | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, BGA16 |
| TPA6130A2RTJRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQCC20 |
| TPA6130A2RTJTG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQCC20 |
| TPA6132A2RTER | 0.025 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC16 |
| TPA6132A2RTET | 0.025 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA6130A2YZHT | 功能描述:音頻放大器 138-mW DirectPath Stereo Headphone Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6132A2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:25-mW DIRECTPATH? STEREO HEADPHONE AMPLIFIER WITH POP SUPPRESSION |
| TPA6132A2EVM2 | 功能描述:音頻 IC 開發工具 TPA6132A2EVM2 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA6132A2RTER | 功能描述:音頻放大器 25mW DirectPath St Headphone Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6132A2RTET | 功能描述:音頻放大器 25mW DirectPath St Headphone Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。