- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS2481PW (TEXAS INSTRUMENTS INC) POWER SUPPLY SUPPORT CKT, PDSO20 PDF資料下載
參數資料
| 型號： | TPS2481PW |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PDSO20 |
| 封裝： | GREEN, PLASTIC, TSSOP-20 |
| 文件頁數： | 3/56頁 |
| 文件大小： | 1381K |
| 代理商： | TPS2481PW |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
LIM
S
50mV
I
R
=
6
F
T
C
1347
10
=
www.ti.com
SLUS939B – APRIL 2010 – REVISED DECEMBER 2010
ground to alter the natural constant power inrush current shape. If properly designed, the effect is to cause the
leading step of current in Figure 12 to look like a ramp. PROG is internally pulled to ground whenever EN, POR,
or UVLO are not satisfied or the TPS2480 is latched off. This feature serves to discharge any capacitance
connected to the pin. Do not apply voltages greater than 4 V to PROG. If the constant power limit is not used,
PROG should be tied to VREF through a 47-k
resistor.
SCL: This pin is the clock input for the I2C interface.
SDA: This pin is the data input for the I2C interface.
SENSE: Monitors the voltage at the drain of the external FET, and the downstream side of RS providing the
constant power limit engine with feedback of both the external FET current (ID) and voltage (VDS). Voltage is
determined by the difference between SENSE and OUT, while the current analog is the difference between VCC
and SENSE. The constant power engine uses VDS to compute the allowed ID and is clamped to 50 mV, acting
like a traditional current limit at low VDS. The maximum current limit is set by the following equation:
(3)
Design the connections to SENSE to minimize RS voltage sensing errors. Don't drive SENSE to a large voltage
difference from VCC because it is internally clamped to VCC. The current limit function can be disabled by
connecting SENSE to VCC.
TIMER: An integrating capacitor, CT, connected to the TIMER pin provides a timing function that controls the
fault-time for both versions and the restart interval for the TPS2481. The timer charges at 25 mA whenever the
TPS2480/81 is in power limit or current limit and discharges at 2.5 mA otherwise. The charge-to-discharge current
ratio is constant with temperature even though there is a positive temperature coefficient to both. If TIMER
reaches 4 V, the TPS2480 pulls GATE to ground, latches off, and discharges CT. The TPS2491 pulls GATE to
ground and attempt a restart (re-enable GATE) after a timing sequence consisting of discharging CT down to 1 V
followed by 15 more charge and discharge cycles. The TPS2480 can be reset by either cycling the EN pin or the
UVLO (e.g. power cycling). TIMER discharges when EN is low or UVLO or POR are active. The TIMER pin
should be tied to ground if this feature is not used. The general equation for fault retry time as a function of CT is:
(4)
VCC: This pin is associated with three functions:
1. biasing power to the integrated circuit,
2. input to power on reset (POR) and under voltage lockout (UVLO) functions, and
3. voltage sense at one terminal of RS for the external FET current measurement.
The voltage must exceed the POR (about 6 V for roughly 400 ms) and the internal UVLO (about 8 V) before
normal operation (driving the GATE) may begin. Connections to VCC should be designed to minimize RS voltage
sensing errors and to maximize the effect of C1 and D1; place C1 at RS rather than at the device pin to eliminate
transient sensing errors. GATE, PROG, PG, and TIMER are held low when either UVLO or POR are active.
VINM: This pin is Kelvin connected to the negative (load) side of the current sensing resistor. It will appear to
external circuitry as a 20-mA sink in parallel with a 320-k resistor to GND.
VINP: This pin is Kelvin connected to the positive (source) side of the current sensing resistor. It will typically sink
~ 20 mA.
VS: Power source for the logic and I2C interface. Typically between 3 V and 5 V.
VREF: Provides a 4.0-V reference voltage for use in conjunction with the resistor divider of a typical application
circuit to set the voltage on the PROG pin. The reference voltage is available once the internal POR and UVLO
thresholds have been met. It is not designed as a supply voltage for other circuitry, therefore ensure that no more
than 1 mA is drawn. Although not typically required, up to 1000 pF can be placed on this pin.
Copyright 2010, Texas Instruments Incorporated
11
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2480PW | POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPS2490DGSRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS2490DGSR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS2490DGSG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS2490DGS | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2481PWR | 功能描述:熱插拔功率分布 Pos VltgInt Prot Dev/Hotswap Cntrlr RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2482PW | 制造商:Texas Instruments 功能描述:Hot Swap Controller 1-CH 80V 20-Pin TSSOP Tube 制造商:Texas Instruments 功能描述:IC CTRLR HOT SWAP 9-36V 20TSSOP 制造商:Texas Instruments 功能描述:36V Hotswap Cntlr w/ Digital Pwr Monitor |
| TPS2482PWR | 制造商:Texas Instruments 功能描述:Hot Swap Controller 1-CH 80V 20-Pin TSSOP T/R 制造商:Texas Instruments 功能描述:36V Hotswap Cntlr w/ Digital Pwr Monitor |
| TPS2483EVM-157 | 功能描述:電源管理IC開發工具 TPS2483 EVAL MOD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2483PW | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 20-TSSOP 制造商:texas instruments 系列:- 包裝:管件 零件狀態:有效 類型:熱交換控制器，監控器 通道數:1 內部開關:無 應用:通用 特性:自動重試，I2C，UVLO 可編程特性:限流，故障超時 電壓 - 電源:9 V ~ 80 V 電流 - 輸出（最大值）:- 工作溫度:-40°C ~ 85°C 電流 - 電源:2mA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:20-TSSOP 功能引腳:EN，PG，PROG，TIMER 標準包裝:70 |
發布緊急采購，3分鐘左右您將得到回復。