- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS2540RTET (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 PDF資料下載
參數資料
| 型號： | TPS2540RTET |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| 封裝： | GREEN, PLASTIC, WQFN-16 |
| 文件頁數： | 24/37頁 |
| 文件大?。?/td> | 999K |
| 代理商： | TPS2540RTET |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
SLVSAG2A
– OCTOBER 2010 – REVISED APRIL 2011
Layout Guidelines
TPS2540/40A/41 Placement: Place the TPS2540/40A/41 near the USB output connector and 150-
F OUT pin
filter capacitor. Connect the exposed Power PAD to the GND pin and to the system ground plane using a via
array.
IN pin bypass capacitance: Place the 0.1-
F bypass capacitor near the IN pin and make the connection using a
low inductance trace.
D+ and D- Traces: Route in and out traces as controlled impedance differential pairs per the USB specification
and the Intel guideline for USB-2.0. Minimize the use of vias in the high speed data lines.
ESD
The use of a common mode choke in the upstream datapath can provide additional ESD protection from client
side cable insertion transients. In addition, a low capacitance ESD protection array such as the TPD2E001
provides a robust solution. The TPS2540EVM-623 (SLVU401) provides a good example of routing and output
datapath protection.
Using a system board, applying same design rules and protection devices as the TPS2540EVM-623 , the
TPS2540 has been tested to EN61000-4-2. The levels used were 8-kV contact discharge and 15-kV air
discharge. Voltage transients were applied between D+ terminal and the earth ground, and between D- terminal
and the earth ground, V- being connected to earth ground. Tests were performed while both powered and
unpowered. No TPS2540 failures were observed and operation was continuous.
IN Pin Bypass Capacitance
Place the 0.1-
F bypass capacitor near the IN pin and make the connection using a low inductance trace.
ILIM0 and ILIM1 Pin Connections
Current limit set point accuracy can be compromised by stray leakage from a higher voltage source to the ILIM0
or ILIM1 pins. Ensure that there is adequate spacing between IN pin copper/trace and ILIM0 pin trace to prevent
contaminant buildup during the PCB assembly process. If a low current limit set point is required (RILIMx
> 200
k
Ω), use ILIM1 for this case as it is further away from the IN pin.
REVISION HISTORY
Changes from Original (October 2010) to Revision A
Page
Added TPS2540A device to the datasheet. .......................................................................................................................... 1
Deleted All (Draft) notations for BC1.2. ................................................................................................................................ 1
Added Longer Detach Detection Time (TPS2540A) bullet. .................................................................................................. 1
Changed Typical Application Diagram. ................................................................................................................................. 1
Added TPS2540A description information. ........................................................................................................................... 2
Added Low DP_IN period in DCP mode information for the TPS2540A device .................................................................. 6
Changed pinout drawing. ...................................................................................................................................................... 7
Changed TPS2540/40A Control Signal drawing. ................................................................................................................ 29
30
Copyright
2010–2011, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2541RTET | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| TPS2550DBV | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| TPS2551DRVR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| TPS2551DRVTG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| TPS2551DRVRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2540RTET | 制造商:Texas Instruments 功能描述:IC USB SWITCH 2.6GHZ 16-WQFN |
| TPS2541ARTER | 功能描述:電源開關 IC - USB USB Charging Port Pwr Sw & Controller RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| TPS2541ARTET | 功能描述:電源開關 IC - USB USB Charging Port Pwr Sw & Controller RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| TPS2541RTER | 功能描述:電源開關 IC - USB USB Charging Port Pwr Swtch &Contrller RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| TPS2541RTET | 功能描述:電源開關 IC - USB USB Charging Port Pwr Swtch &Contrller RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。