- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS2551DRVRG4 (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 PDF資料下載
參數資料
| 型號： | TPS2551DRVRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封裝： | GREEN, PLASTIC, SON-6 |
| 文件頁數： | 11/32頁 |
| 文件大小： | 1402K |
| 代理商： | TPS2551DRVRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
POWER DISSIPATION AND JUNCTION TEMPERATURE
UNIVERSAL SERIAL BUS (USB) POWER-DISTRIBUTION REQUIREMENTS
www.ti.com ........................................................................................................................................ SLVS736B – FEBRUARY 2008 – REVISED NOVEMBER 2008
Select the closest 1% resistor greater than the calculated value: RILIM = 21.5 k. This sets the maximum
current-limit threshold at 1.25 A . Use the IOS equations, Figure 21, and the previously calculated value for RILIM
to calculate the minimum resulting current-limit threshold.
R
ILIM = 21.5 k
I
OS(min) (mA) = (39700 V) / ILIM (k))
1.342
I
OS(min) (mA) = (39700 V) / (21.5 (k))
1.342
I
OS(min) = 647 mA
The resulting minimum current-limit threshold is 647 mA with a 21.5 k
resistor.
The low on-resistance of the N-channel MOSFET allows small surface-mount packages to pass large currents. It
is good design practice to estimate power dissipation and junction temperature. The below analysis gives an
approximation for calculating junction temperature based on the power dissipation in the package. However, it is
important to note that thermal analysis is strongly dependent on additional system level factors. Such factors
include air flow, board layout, copper thickness and surface area, and proximity to other devices dissipating
power. Good thermal design practice must include all system level factors in addition to individual component
analysis.
Begin by determining the rDS(on) of the N-channel MOSFET relative to the input voltage and operating
temperature. As an initial estimate, use the highest operating ambient temperature of interest and read rDS(on)
from the typical characteristics graph. Using this value, the power dissipation can be calculated by:
PD = rDS(on) × IOUT
2
Where:
PD = Total power dissipation (W)
rDS(on) = Power switch on-resistance ()
IOUT = Maximum current-limit threshold (A)
This step calculates the total power dissipation of the N-channel MOSFET.
Finally, calculate the junction temperature:
TJ = PD × RΘJA + TA
Where:
TA = Ambient temperature (°C)
RΘJA = Thermal resistance (°C/W)
PD = Total power dissipation (W)
Compare the calculated junction temperature with the initial estimate. If they are not within a few degrees, repeat
the calculation using the "refined" rDS(on) from the previous calculation as the new estimate. Two or three
iterations are generally sufficient to achieve the desired result. The final junction temperature is highly dependent
on thermal resistance RθJA, and thermal resistance is highly dependent on the individual package and board
layout. The "Dissipating Rating Table" at the beginning of this document provides example thermal resistance for
specific packages and board layouts.
One application for this device is for current-limiting in universal serial bus (USB) applications. The original USB
interface was a 12-Mb/s or 1.5-Mb/s, multiplexed serial bus designed for low-to-medium bandwidth PC
peripherals (e.g., keyboards, printers, scanners, and mice). As the demand for more bandwidth increased, the
USB 2.0 standard was introduced increasing the maximum data rate to 480-Mb/s. The four-wire USB interface is
conceived for dynamic attach-detach (hot plug-unplug) of peripherals. Two lines are provided for differential data,
and two lines are provided for 5-V power distribution.
USB data is a 3.3-V level signal, but power is distributed at 5 V to allow for voltage drops in cases where power
is distributed through more than one hub across long cables. Each function must provide its own regulated 3.3 V
from the 5-V input or its own internal power supply. The USB specification classifies two different classes of
Copyright 2008, Texas Instruments Incorporated
19
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2551DBVR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| TPS2554DRCT | POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS2557DRBT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2557DRB | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2561DRC | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2551DRVT | 功能描述:電源開關 IC - USB Adj Crnt-Ltd Pwr Dist Sw RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| TPS2551DRVTG4 | 功能描述:電源開關 IC - USB Adj current Ltd Sw RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| TPS2551QDBVRQ1 | 功能描述:電源開關 IC - USB Adj Crnt-Limited Pwr Distribution Sw RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| TPS2552DBV1EVM-364 | 功能描述:交換機 IC 開發工具 TPS2552DBV1EVM-364 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| TPS2552DBVEVM-364 | 功能描述:交換機 IC 開發工具 TPS2552DBVEVM-364 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
發布緊急采購，3分鐘左右您將得到回復。