- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS3610U18PWG4 (TEXAS INSTRUMENTS INC) 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 PDF資料下載
參數資料
| 型號： | TPS3610U18PWG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| 封裝： | 5.10 X 6.60 MM, GREEN, PLASTIC, TSSOP-14 |
| 文件頁數： | 23/26頁 |
| 文件大小： | 711K |
| 代理商： | TPS3610U18PWG4 |
TPS3610U18, TPS3610T50
BATTERY BACKUP SUPERVISORS FOR RAM RETENTION
SLVS327B – DECEMBER 2000 – REVISED DECEMBER 2002
6
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
NO.
I/O
DESCRIPTION
BATTOK
9
O
Battery status output
BATTON
6
O
Logic output/external bypass switch driver output
CEIN
5
I
Chip-enable input
CEOUT
10
O
Chip-enable output
GND
3
I
Ground
LOWLINE
11
O
Early power-fail warning output
MSWITCH
4
I
Manual switch to force device into battery-backup mode
VOUT
1
O
Supply output
PFI
7
I
Power-fail comparator input
PFO
8
O
Power-fail comparator output
RESET
13
O
Active-low reset output
VBAT
14
I
Backup-battery input
VDD
2
I
Input supply voltage
WDI
12
I
Watchdog timer input
detailed description
battery freshness seal
The battery freshness seal of the TPS3610 family disconnects the backup battery from internal circuitry until
it is needed. This function ensures that the backup battery connected to VBAT is fresh when the final product
is put to use. The following steps explain how to enable the freshness seal mode:
1.
Connect VBAT (VBAT > VBATmin)
2.
Ground PFO
3.
Connect PFI to VDD (PFI = VDD)
4.
Connect VDD to power supply (VDD > VIT) and keep connected for 5 ms < t < 35 ms
The battery freshness seal mode is disabled by the positive-going edge of RESET when VDD is applied.
BATTOK output
BATTOK is a logic feedback of the device to indicate the status of the backup battery. The supervisor checks
the battery voltage every 200 ms with a voltage divider load of approximately 100 k
and a measurement cycle
on-time of 25
s. The measurement cycle starts after the reset is released. If the battery voltage VBAT is below
the negative-going threshold voltage VIT(BOK), the indicator BATTOK does a high-to-low transition. Otherwise
it retains its status to VDD level.
25
s
IBAT
200 ms
100
A
t
Figure 1. BATTOK Timing
相關PDF資料 |
PDF描述 |
|---|---|
| TPS3610T50PWRG4 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| TPS3610U18PW | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| TPS3618-50DGKTG4 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| TPS3618-50DGKT | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| TPS3705-33Y | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, UUC8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS3610U18PWR | 功能描述:監控電路 Battery-Backup for RAM Retention RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TPS3610U18PWRG4 | 功能描述:監控電路 Battery-Backup for RAM Retention RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TPS3610U25PWR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| TPS3610U30PWR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| TPS3610U33PWR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。